Прошивка планшета на AllWinner A23

[чипега]

GT90H v1.3

у моего планшета такая же плата,но вчера я от него избавился
вот

[kuk6okcep47]

GT90H-V1.3_HT-a23_256M_5990_gt90h_800x480-0309x2_20141007-N8000.rar - вот эту ставил и разрешение поменял на 120. Он поработает и начинаются проблемы, перезагрузки, отказы google service's ... короче одни муки

[1024]

Хелп.
Есть китайский N8000 64Gb с разбитым тачем. Решил как-то оживить, подрубил по адб, поковырялся в build.prop (конкретнее - включил отладку по юсб), залил - и планшет перестал загружаться. То есть показывает при включении две статических картинки, а третью, анимацию, крутит до бесконечности.
Почитав тему, решил поступить так, будто бы у меня кирпич - т.е. манипуляции с чипом памяти. Нагуглил даташит на память, замыкаю, так и сяк - устройство определяется как USB Device(VID_1f3a_PID_efe8), но ни один из прошивальщиков планшет не видит вообще. К тому же, после сих действий с иголкой и чипом планшет и вовсе перестал включаться - симптомы обычные, кирпичные: светодиод при питании горит, на кнопки не реагирует. Так как я НЕ ПРОШИВАЛ ничего, и не замыкал контактов, кроме нужных, я вообще не могу понять, что пошло не так.
Помогите, пожалуйста.
Инфа о планшете:
На корпусе SAMSUNG 64GB Wi-Fi GALAXY NOTE N8000
Проц Allwinner A23
На матери: GT90H-V1.2 2014/04/10
Память SKHynix H27UBG8T2CTR

[maxxis777]

Помогите найти прошиву для Manta MID721 Tablet 7"
AllWinner A23
android 4.4
512 Mb Ram
4Gb rom
wifi esp8089
на плате AL-Ax3-Q8-V1.1 2015-01-21
камера только фронт
на шлейфе тача только XLD 30pin
с польского сайта не могу скачать, тупо не открывает страницу
http://www.manta.info.pl/forum/ogolnie- ... lash-tool/

[BoyPlay]

Приветствую Всех!!
Подскажите, возможно ли взамен прошивки LT1002D поставить другую получше и с нормальной разметкой памяти?
Заранее спасибо.

[Stalmon]

Помогите подобрать прошивку на китайский планшет
Процессор DualCore-A23
Модель Q8H
Версия Android 4.2.2
Firmware version v2.0.9
Версия ядра 3.4.39
Материнская плата Q8H-V5 2013-12-26
Номер сборки polaris-eng 4.2.2 8089 20140106 test-keys

[1971Djon]

С Наступающим всех! Люди подскажите проц. AllWinner A23 плата GT90H-v1.3 прошивка GT90H-V1.3-wifi5990p-(4_4_2_ROOT)-RC1.7z после прошивки получил кирпич. Не включается не заряжается комп не видит. Прошивал Phoenix Suit по инструкции как восстановить? чем? Спасибо!

[Aleksandr45ru]

Подскажите где можно взять twrp для mapan mx 723

Отправлено спустя 55 минут 19 секунд:
Помагите найти twrp для mapan mx723

Отправлено спустя 3 минуты 23 секунды:
Помагите найти twrp для mapan mx723

[deyv]

Попался такой зверь не вк A23 t900-mainboard-v2.0.2014\04\29 jtx прошил T900-92G запустился но не работает сенсор микруха на сенсор стоит GSL1680 c3f1075357n перепробовал кучу прошивок не одна не подходит.Вот сейчас стоит прошивка
A23Q6(P1) System configration

;---------------------------------------------------------------------------------------------------------
; port configuration:
; port_name = port:GPIO<mux><pull up/down><driver level><default value>
; mux: GPIO function configuration, 0-input, 1-output, 2+: special funciton for modules
; pull up/down: 1-pull up, 2-pull down
; driver level: 0,1,2,3. 2 is recommended
; default value: default output value when this IO is configured as an output IO
;---------------------------------------------------------------------------------------------------------

[product]
version = "100"
machine = "a23-t900"

[platform]
eraseflag = 1
;next_work = 5
;----------------------------------------------------------------------------------
;[target] system bootup configuration
;boot_clock = CPU boot frequency, Unit: MHz
;storage_type = boot medium, 0-nand, 1-card0, 2-card2, -1(defualt)auto scan
;----------------------------------------------------------------------------------
[target]
boot_clock = 1008
storage_type = -1

;----------------------------------------------------------------------------------
;dcdc1_vol ---set dcdc1 voltage,mV,1600-3400,100mV/step
;dcdc2_vol ---set dcdc2 voltage,mV,600-1540,20mV/step
;dcdc3_vol ---set dcdc3 voltage,mV,600-1860,20mV/step
;dcdc4_vol ---set dcdc4 voltage,mV,600-1540,20mV/step
;dcdc5_vol ---set dcdc5 voltage,mV,1000-2550,50mV/step
;aldo2_vol ---set aldo2 voltage,mV,700-3300,100mV/step
;aldo3_vol ---set aldo3 voltage,mV,700-3300,100mV/step
;----------------------------------------------------------------------------------
[power_sply]
dcdc1_vol = 3000
dcdc2_vol = 1160
dcdc3_vol = 1260
dcdc4_vol = 0
dcdc5_vol = 1550
aldo2_vol = 2500
aldo3_vol = 3000

;----------------------------------------------------------------------------------
;card boot
;----------------------------------------------------------------------------------
[card_boot]
logical_start = 40960
sprite_gpio0 =

;----------------------------------------------------------------------------------
;[cardx_boot_para] boot card configuration
;card_ctrl = boot card NO. 0 or 2
;card_high_speed = speed mode, 0-normal mode(up to 25MHz), 1-high speed mode(up to 50MHz)
;card_line = boot card buswidth(1 or 4)
;----------------------------------------------------------------------------------
[card0_boot_para]
card_ctrl = 0
card_high_speed = 1
card_line = 4
sdc_d1 = port:PF0<2><1><2><default>
sdc_d0 = port:PF1<2><1><2><default>
sdc_clk = port:PF2<2><1><2><default>
sdc_cmd = port:PF3<2><1><2><default>
sdc_d3 = port:PF4<2><1><2><default>
sdc_d2 = port:PF5<2><1><2><default>

[card2_boot_para]
card_ctrl = 2
card_high_speed = 1
card_line = 4
sdc_clk = port:PC05<3><1><2><default>
sdc_cmd = port:PC06<3><1><2><default>
sdc_d0 = port:PC08<3><1><2><default>
sdc_d1 = port:PC09<3><1><2><default>
sdc_d2 = port:PC10<3><1><2><default>
sdc_d3 = port:PC11<3><1><2><default>

;----------------------------------------------------------------------------------
;[twi_para] twi for boot code
;twi_port = twi controller ID
;----------------------------------------------------------------------------------
[twi_para]
twi_port = 0
twi_scl = port:PH02<2><default><default><default>
twi_sda = port:PH03<2><default><default><default>

;----------------------------------------------------------------------------------
;[uart_para] boot debug port configuration
;uart_debug_port = uart port ID for boot debug
;----------------------------------------------------------------------------------
[uart_para]
uart_debug_port = 1
uart_debug_tx = port:PF02<3><1><default><default>
uart_debug_rx = port:PF04<3><1><default><default>

;----------------------------------------------------------------------------------
;[jtag_para] jtag configuration
;jtag_enable = 0-disable jtag, 1-enable jtag
;----------------------------------------------------------------------------------
[jtag_para]
jtag_enable = 0
jtag_ms = port:PF00<3><default><default><default>
jtag_ck = port:PF05<3><default><default><default>
jtag_do = port:PF03<3><default><default><default>
jtag_di = port:PF01<3><default><default><default>

;----------------------------------------------------------------------------------
;[clock] pll configuration
;----------------------------------------------------------------------------------
[clock]
pll3 = 297
pll4 = 300
pll6 = 600
pll8 = 408
pll9 = 480
pll10 = 468

;---------------------------------------------------------------------------------------------------------
;[pm_para] power management
;standby_mode = 0-normal standby, 1-super standby
;---------------------------------------------------------------------------------------------------------
[pm_para]
standby_mode = 1

;*****************************************************************************
;sdram configuration
;
;*****************************************************************************
[dram_para]
;dram_clk = 552
dram_clk = 456
dram_type = 3
dram_zq = 0xBB7B
dram_odt_en = 1
dram_para1 = 0x1102400
dram_para2 = 0
dram_mr0 = 0x1A50
dram_mr1 = 0x4
dram_mr2 = 0x10
dram_mr3 = 0
dram_tpr0 = 0xAB83DEF
dram_tpr1 = 0x6052080
dram_tpr2 = 0xD034
dram_tpr3 = 0x448C5533
dram_tpr4 = 0x08010D00
dram_tpr5 = 0x340B20F
dram_tpr6 = 0x20D118CC
dram_tpr7 = 0x14062485
dram_tpr8 = 0x220D1D52
dram_tpr9 = 0x1E078C22
dram_tpr10 = 0x3C
dram_tpr11 = 0
dram_tpr12 = 162
dram_tpr13 = 0x30000

;---------------------------------------------------------------------------------------------------------
; wakeup_src_para:
; sometimes, u would like to add more wakeup src in standby mode, these para will be
; help;
; u need to make sure the standby mode support the wakeup src. Also, some hw
; condition must be guaranteed.
; including:
; cpu_en: power on or off.
; 1: mean power on
; 0: mean power off
; cpu_freq: indicating lowest freq. unit is Mhz;
; dram selfresh_en: selfresh or not.
; 1: enable enter selfresh
; 0: disable enter selfresh
; dram_pll: if not enter selfresh, indicating lowest freq. unit is Mhz;
; wakeup_src: to make the scenario work, the wakeup src is needed.
;---------------------------------------------------------------------------------------------------------
[wakeup_src_para]
cpu_en = 0
cpu_freq = 48
; (cpu:apb:ahb)
pll_ratio = 0x111
dram_selfresh_en= 1
dram_freq = 36

;----------------------------------------------------------------------------------
;i2c configuration
; twi_used = twix enable
;----------------------------------------------------------------------------------
[twi0]
twi_used = 1
twi_scl = port:PH02<2><default><default><default>
twi_sda = port:PH03<2><default><default><default>

[twi1]
twi_used = 1
twi_scl = port:PH04<2><default><default><default>
twi_sda = port:PH05<2><default><default><default>

[twi2]
twi_used = 1
twi_scl = port:PE12<3><default><default><default>
twi_sda = port:PE13<3><default><default><default>


;----------------------------------------------------------------------------------
;uart configuration
;uart_used = uart x enable
;uart_type = 2:2 wire,4:4 wire,8:8 wire, full function
;----------------------------------------------------------------------------------
[uart0]
uart_used = 1
uart_port = 0
uart_type = 2
uart_tx = port:PF02<3><1><default><default>
uart_rx = port:PF04<3><1><default><default>

[uart1]
uart_used = 0
uart_type = 4
uart_tx = port:PG06<2><1><default><default>
uart_rx = port:PG07<2><1><default><default>
uart_rts = port:PG08<2><1><default><default>
uart_cts = port:PG09<2><1><default><default>

[uart2]
uart_used = 1
uart_type = 4
uart_tx = port:PB00<2><1><default><default>
uart_rx = port:PB01<2><1><default><default>
uart_rts = port:PB02<2><1><default><default>
uart_cts = port:PB03<2><1><default><default>

[uart3]
uart_used = 0
uart_type = 4
uart_tx = port:PH06<3><1><default><default>
uart_rx = port:PH07<3><1><default><default>
uart_rts = port:PH08<3><1><default><default>
uart_cts = port:PH09<3><1><default><default>

[uart4]
uart_used = 0
uart_port = 4
uart_type = 2
uart_tx = port:PA04<2><1><default><default>
uart_rx = port:PA05<2><1><default><default>
uart_rts = port:PA06<2><1><default><default>
uart_cts = port:PA07<2><1><default><default>

;----------------------------------------------------------------------------------
;SPI controller configuration
;spi_used = SPIx enable
;spi_cs_bitmap = SPI bit mapping
;----------------------------------------------------------------------------------
[spi0]
spi_used = 0
spi_cs_bitmap = 1
spi_mosi = port:PC00<3><default><default><default>
spi_miso = port:PC01<3><default><default><default>
spi_sclk = port:PC02<3><default><default><default>
spi_cs0 = port:PC03<3><1><default><default>

[spi1]
spi_used = 0
spi_cs_bitmap = 1
spi_cs0 = port:PA00<2><1><default><default>
spi_sclk = port:PA01<2><default><default><default>
spi_mosi = port:PA02<2><default><default><default>
spi_miso = port:PA03<2><default><default><default>

;----------------------------------------------------------------------------------
;SPI device configuration
;spi_dev_num: number of spi devices
;----------------------------------------------------------------------------------
[spi_devices]
spi_dev_num = 0

;----------------------------------------------------------------------------------
;[spi_board0] spi device configuration
;modalias = spi device name
;max_speed_hz = max transfer speed
;bus_num = bus ID
;chip_select = chip select, 0,1
;mode = SPI transfer mode
;----------------------------------------------------------------------------------
[spi_board0]
modalias = "at25df641"
max_speed_hz = 50000000
bus_num = 0
chip_select = 0
mode = 0


;----------------------------------------------------------------------------------
;capacitor tp configuration
;ctp_twi_id : twi controller ID
;ctp_twi_addr : I2C slave address, 7bit
;ctp_screen_max_x/_y : resolution of touch panel
;ctp_revert_x/_y_flag : whether need to revert x/y
;ctp_exchange_x_y_flag: whether need to exchange the value of x and y
;ctp_int_port : port for tp's interrupt signal
;ctp_wakeup : port for wakeup tp
;----------------------------------------------------------------------------------
[ctp_para]
ctp_used = 1
;ctp_name = "gsl1680e_t736"
;ctp_name = "gsl1680e_t735"
;ctp_name = "gsl1680e_t739"
;ctp_name = "gsl1680e_t739_m"
;ctp_name = "gsl1680e_t900"
ctp_name = "gsl1680e_t900_p"
;ctp_name = "gsl1680e_t786"
ctp_twi_id = 0
ctp_twi_addr = 0x40
ctp_screen_max_x = 800
ctp_screen_max_y = 480
ctp_revert_x_flag = 0
ctp_revert_y_flag = 0
ctp_exchange_x_y_flag = 0

ctp_int_port = port:PB05<4><default><default><default>
ctp_wakeup = port:PL10<1><default><default><1>

;--------------------------------------------------------------------------------
; CTP automatic detection configuration
;ctp_detect_used --- Whether startup automatic inspection function. 1:used,0:unused
;Module name postposition 1 said detection, 0 means no detection.
;--------------------------------------------------------------------------------
[ctp_list_para]
ctp_det_used = 1
ft5x_ts = 1
gt82x = 1
gslX680 = 0
gslX680new = 1
gt9xx_ts = 1
gt9xxf_ts = 0
;gt811 = 1
tu_ts = 0
gt818 = 1
zet622x = 1
aw5306_ts = 1
;----------------------------------------------------------------------------------
;touch key configuration
;tkey_twi_id : twi controller ID
;tkey_twi_addr : I2C slave address, 7bit
;tkey_int : port for touch key's interrupt signal
;----------------------------------------------------------------------------------
[tkey_para]
tkey_used = 0
tkey_twi_id =
tkey_twi_addr =
tkey_int =

;----------------------------------------------------------------------------------
;motor configuration
;motor_shake : port for making the moto shaking
;----------------------------------------------------------------------------------
[motor_para]
motor_used = 1
;motor_shake = port:power3<1><default><default><1>
motor_ldo = axp22_dldo4
motor_ldo_voltage = 3300

;----------------------------------------------------------------------------------
;thermal configuration
;----------------------------------------------------------------------------------
[ths_para]
ths_used = 1

;----------------------------------------------------------------------------------
;[nandx_para]
;nand_support_2ch = support dual channel
;nand0_used = nand0使能标识
;----------------------------------------------------------------------------------
[nand0_para]
nand_support_2ch = 0

nand0_used = 0
nand0_we = port:PC00<2><default><default><default>
nand0_ale = port:PC01<2><default><default><default>
nand0_cle = port:PC02<2><default><default><default>
nand0_ce1 = port:PC03<2><default><default><default>
nand0_ce0 = port:PC04<2><default><default><default>
nand0_nre = port:PC05<2><default><default><default>
nand0_rb0 = port:PC06<2><default><default><default>
nand0_rb1 = port:PC07<2><default><default><default>
nand0_d0 = port:PC08<2><default><default><default>
nand0_d1 = port:PC09<2><default><default><default>
nand0_d2 = port:PC10<2><default><default><default>
nand0_d3 = port:PC11<2><default><default><default>
nand0_d4 = port:PC12<2><default><default><default>
nand0_d5 = port:PC13<2><default><default><default>
nand0_d6 = port:PC14<2><default><default><default>
nand0_d7 = port:PC15<2><default><default><default>
nand0_ndqs = port:PC16<2><default><default><default>
nand0_ce2 = port:PC17<2><default><default><default>
nand0_ce3 = port:PC18<2><default><default><default>

;----------------------------------------------------------------------------------
;disp init configuration
;
;disp_mode (0:screen0<screen0,fb0>)
;screenx_output_type (0:none; 1:lcd; 3:hdmi;)
;screenx_output_mode (used for hdmi output, 0:480i 1:576i 2:480p 3:576p 4:720p50)
; (5:720p60 6:1080i50 7:1080i60 8:1080p24 9:1080p50 10:1080p60)
;fbx format (4:RGB655 5:RGB565 6:RGB556 7:ARGB1555 8:RGBA5551 9:RGB888 10:ARGB8888 12:ARGB4444)
;fbx pixel sequence (0:ARGB 1:BGRA 2:ABGR 3:RGBA)
;fb0_scaler_mode_enable(scaler mode enable, used FE)
;fbx_width,fbx_height (framebuffer horizontal/vertical pixels, fix to output resolution while equal 0)
;lcdx_backlight (lcd init backlight,the range:[0,256],default:197
;lcdx_yy (lcd init screen bright/contrast/saturation/hue, value:0~100, default:50/50/57/50)
;lcd0_contrast (LCD contrast, 0~100)
;lcd0_saturation (LCD saturation, 0~100)
;lcd0_hue (LCD hue, 0~100)
;----------------------------------------------------------------------------------
[disp_init]
disp_init_enable = 1
disp_mode = 0

screen0_output_type = 1
screen0_output_mode = 4

screen1_output_type = 1
screen1_output_mode = 4

fb0_format = 10
fb0_pixel_sequence = 0
fb0_scaler_mode_enable = 0
fb0_width = 0
fb0_height = 0

fb1_format = 10
fb1_pixel_sequence = 0
fb1_scaler_mode_enable = 0
fb1_width = 0
fb1_height = 0

lcd0_backlight = 197
lcd1_backlight = 197

lcd0_bright = 50
lcd0_contrast = 50
lcd0_saturation = 57
lcd0_hue = 50

lcd1_bright = 50
lcd1_contrast = 50
lcd1_saturation = 57
lcd1_hue = 50

;----------------------------------------------------------------------------------
;lcd0 configuration

;lcd_if: 0:hv(sync+de); 1:8080; 2:ttl; 3:lvds; 4:dsi; 5:edp; 6:extend dsi
;lcd_x: lcd horizontal resolution
;lcd_y: lcd vertical resolution
;lcd_width: width of lcd in mm
;lcd_height: height of lcd in mm
;lcd_dclk_freq: in MHZ unit
;lcd_pwm_freq: in HZ unit
;lcd_pwm_pol: lcd backlight PWM polarity
;lcd_pwm_max_limit lcd backlight PWM max limit(<=255)
;lcd_hbp: hsync back porch
;lcd_ht: hsync total cycle
;lcd_vbp: vsync back porch
;lcd_vt: vysnc total cycle
;lcd_hspw: hsync plus width
;lcd_vspw: vysnc plus width
;lcd_lvds_if: 0:single link; 1:dual link
;lcd_lvds_colordepth: 0:8bit; 1:6bit
;lcd_lvds_mode: 0:NS mode; 1:JEIDA mode
;lcd_frm: 0:disable; 1:enable rgb666 dither; 2:enable rgb656 dither
;lcd_io_phase: 0:noraml; 1:intert phase(0~3bit: vsync phase; 4~7bit:hsync phase;
; 8~11bit:dclk phase; 12~15bit:de phase)
;lcd_gamma_en lcd gamma correction enable
;lcd_bright_curve_en lcd bright curve correction enable
;lcd_cmap_en lcd color map function enable
;deu_mode 0:smoll lcd screen; 1:large lcd screen(larger than 10inch)
;lcdgamma4iep: Smart Backlight parameter, lcd gamma vale * 10;
; decrease it while lcd is not bright enough; increase while lcd is too bright
;smart_color 90:normal lcd screen 65:retina lcd screen(9.7inch)
;----------------------------------------------------------------------------------
[lcd0_para]
lcd_used = 1

lcd_driver_name = "default_lcd"
lcd_if = 0
lcd_x = 800
lcd_y = 480
lcd_width = 154
lcd_height = 86
lcd_dclk_freq = 33
lcd_pwm_used = 1
lcd_pwm_ch = 0
lcd_pwm_freq = 10000
lcd_pwm_pol = 0
lcd_hbp = 46
lcd_ht = 1055
lcd_hspw = 0
lcd_vbp = 23
lcd_vt = 525
lcd_vspw = 0
lcd_lvds_if = 0
lcd_lvds_colordepth = 0
lcd_lvds_mode = 0
lcd_frm = 1
lcd_io_phase = 0x0000
lcd_gamma_en = 0
lcd_bright_curve_en = 0
lcd_cmap_en = 0

;**************** HD ****************
;lcd_driver_name = "default_lcd"
;lcd_if = 0
;lcd_x = 1024
;lcd_y = 600
;lcd_width = 154
;lcd_height = 87
;lcd_dclk_freq = 51
;lcd_pwm_used = 1
;lcd_pwm_ch = 0
;lcd_pwm_freq = 50000
;lcd_pwm_pol = 0
;lcd_hbp = 160
;lcd_ht = 1344
;lcd_hspw = 20
;lcd_vbp = 23
;lcd_vt = 635
;lcd_vspw = 3
;lcd_lvds_if = 0
;lcd_lvds_colordepth = 0
;lcd_lvds_mode = 0
;lcd_frm = 1
;lcd_io_phase = 0x0000
;lcd_gamma_en = 0
;lcd_bright_curve_en = 0
;lcd_cmap_en = 0

deu_mode = 0
lcdgamma4iep = 22
smart_color = 90

lcd_gpio_0 = port:PH07<1><0><default><1>
lcd_bl_en = port:PH06<1><0><default><1>
lcd_power = port:power2<1><0><default><1>

lcdd0 = port:PD00<2><0><default><default>
lcdd1 = port:PD01<2><0><default><default>
lcdd2 = port:PD02<2><0><default><default>
lcdd3 = port:PD03<2><0><default><default>
lcdd4 = port:PD04<2><0><default><default>
lcdd5 = port:PD05<2><0><default><default>
lcdd6 = port:PD06<2><0><default><default>
lcdd7 = port:PD07<2><0><default><default>
lcdd8 = port:PD08<2><0><default><default>
lcdd9 = port:PD09<2><0><default><default>
lcdd10 = port:PD10<2><0><default><default>
lcdd11 = port:PD11<2><0><default><default>
lcdd12 = port:PD12<2><0><default><default>
lcdd13 = port:PD13<2><0><default><default>
lcdd14 = port:PD14<2><0><default><default>
lcdd15 = port:PD15<2><0><default><default>
lcdd16 = port:PD16<2><0><default><default>
lcdd17 = port:PD17<2><0><default><default>
lcdd18 = port:PD18<2><0><default><default>
lcdd19 = port:PD19<2><0><default><default>
lcdd20 = port:PD20<2><0><default><default>
lcdd21 = port:PD21<2><0><default><default>
lcdd22 = port:PD22<2><0><default><default>
lcdd23 = port:PD23<2><0><default><default>
lcdclk = port:PD24<2><0><default><default>
lcdde = port:PD25<2><0><default><default>
lcdhsync = port:PD26<2><0><default><default>
lcdvsync = port:PD27<2><0><default><default>


;----------------------------------------------------------------------------------
;pwm config
;----------------------------------------------------------------------------------
[pwm0_para]
pwm_used = 1
pwm_positive = port:PH00<2><0><default><default>

[pwm1_para]
pwm_used = 0
pwm_positive = port:PH01<2><0><default><default>

[camera_list_para]
camera_list_para_used = 1
ov7670 = 0
gc0308 = 1
gt2005 = 0
hi704 = 0
sp0838 = 1
mt9m112 = 0
mt9m113 = 0
gc2035 = 1
ov2655 = 0
hi253 = 0
gc0307 = 0
mt9d112 = 0
ov5640 = 0
ov5647 = 0
gc2015 = 0
ov2643 = 0
gc0328 = 1
gc0329 = 1
gc0309 = 1
tvp5150 = 0
s5k4ec = 0
ov5650_mv9335 = 0
siv121d = 1
sp0a19 = 1
gc0311 = 1
sp2518 = 1
bf3703 = 1
;--------------------------------------------------------------------------------
;vip (video input port) configuration
;vip_used: 0:disable 1:enable
;vip_mode: 0:sample one interface to one buffer 1:sample two interface to one buffer
;vip_dev_qty: The quantity of devices linked to capture bus
;vip_dev(x)_isp_used 0: not use isp 1:use isp
;vip_dev(x)_fmt: 0:yuv 1:bayer raw rgb
;vip_dev(x)_stby_mode: 0:not shut down power at standby 1:shut down power at standby
;vip_dev(x)_vflip: flip in vertical direction 0:disable 1:enable
;vip_dev(x)_hflip: flip in horizontal direction 0:disable 1:enable
;vip_dev(x)_iovdd: camera module io power handle string, pmu power supply
;vip_dev(x)_iovdd_vol: camera module io power voltage, pmu power supply
;vip_dev(x)_avdd: camera module analog power handle string, pmu power supply
;vip_dev(x)_avdd_vol: camera module analog power voltage, pmu power supply
;vip_dev(x)_dvdd: camera module core power handle string, pmu power supply
;vip_dev(x)_dvdd_vol: camera module core power voltage, pmu power supply
;vip_dev(x)_afvdd: camera module vcm power handle string, pmu power supply
;vip_dev(x)_afvdd_vol: camera module vcm power voltage, pmu power supply
;x indicates the index of the devices which are linked to the same capture bus
;fill voltage in uV, e.g. iovdd = 2.8V, vip_devx_iovdd_vol = 2800000
;fill handle string as below:
;axp22_eldo3
;axp22_dldo4
;axp22_eldo2
;fill handle string "" when not using any pmu power supply
;--------------------------------------------------------------------------------

[csi0]

vip_used = 1
vip_mode = 0
vip_dev_qty = 2
vip_csi_pck = port:PE00<2><default><default><default>
vip_csi_mck = port:PE01<2><default><default><default>
vip_csi_hsync = port:PE02<2><default><default><default>
vip_csi_vsync = port:PE03<2><default><default><default>
vip_csi_d0 = port:PE04<2><default><default><default>
vip_csi_d1 = port:PE05<2><default><default><default>
vip_csi_d2 = port:PE06<2><default><default><default>
vip_csi_d3 = port:PE07<2><default><default><default>
vip_csi_d4 = port:PE08<2><default><default><default>
vip_csi_d5 = port:PE09<2><default><default><default>
vip_csi_d6 = port:PE10<2><default><default><default>
vip_csi_d7 = port:PE11<2><default><default><default>

vip_dev0_mname = "gc0308"
vip_dev0_lane = 1
vip_dev0_twi_id = 2
vip_dev0_twi_addr = 0x42
vip_dev0_isp_used = 0
vip_dev0_fmt = 0
vip_dev0_stby_mode = 0
vip_dev0_vflip = 0
vip_dev0_hflip = 0
vip_dev0_facing = 0
vip_dev0_iovdd = "axp22_dldo3"
vip_dev0_iovdd_vol = 2800000
vip_dev0_avdd = "axp22_ldoio0"
vip_dev0_avdd_vol = 2800000
vip_dev0_dvdd = "axp22_eldo2"
vip_dev0_dvdd_vol = 1800000
vip_dev0_afvdd = ""
vip_dev0_afvdd_vol = 2800000
vip_dev0_power_en =
vip_dev0_reset = port:PE14<1><default><default><0>
vip_dev0_pwdn = port:PE15<1><default><default><1>
vip_dev0_flash_used = 1
vip_dev0_flash_en = port:PL11<1><default><default><0>
vip_dev0_flash = "axp22_eldo3"
vip_dev0_flash_vol = 3300000
vip_dev0_torch_vol = 3000000
vip_dev0_flash_mode =
vip_dev0_af_pwdn =

vip_dev1_mname = "gc0329"
vip_dev1_lane = 1
vip_dev1_twi_id = 2
vip_dev1_twi_addr = 0x62
vip_dev1_isp_used = 0
vip_dev1_fmt = 0
vip_dev1_stby_mode = 0
vip_dev1_vflip = 0
vip_dev1_hflip = 0
vip_dev1_facing = 1
vip_dev1_iovdd = "axp22_dldo3"
vip_dev1_iovdd_vol = 2800000
vip_dev1_avdd = "axp22_ldoio0"
vip_dev1_avdd_vol = 2800000
vip_dev1_dvdd = "axp22_eldo2"
vip_dev1_dvdd_vol = 1800000
vip_dev1_afvdd = ""
vip_dev1_afvdd_vol = 2800000
vip_dev1_power_en =
vip_dev1_reset = port:PE14<1><default><default><0>
vip_dev1_pwdn = port:PE17<1><default><default><1>
vip_dev1_flash_used = 0
vip_dev1_flash_en =
vip_dev1_flash_mode =
vip_dev1_af_pwdn =


;-------------------------------------------------------------------------------
; mmc configuration
;
; Config Guide
; sdc_used: 1-enable card, 0-disable card
; sdc_detmode: card detect mode
; 1-detect card by gpio polling
; 2-detect card by gpio irq(must use IO with irq function)
; 3-no detect, always in for boot card
; 4-manually insert and remove by /proc/driver/sunxi-mmc.x/insert
; sdc_buswidth: card bus width, 1-1bit, 4-4bit, 8-8bit
; sdc_use_wp: 1-with write protect IO, 0-no write protect IO
; sdc_isio: for sdio card
; sdc_regulator: power control.if card supports UHS-I/DDR and HS200 timing for
; SD3.0 or eMMC4.5, regulator must be configured. the value is
; the ldo name of AXP221, eg: sdc_regulator = "axp22_eldo2"
; other: GPIO Mapping configuration
;
; Note:
; 1 if detmode=2, sdc_det's config=6
; else if detmode=1, sdc_det's config=0
; else sdc_det IO is not necessary
; 2 if the customer wants to support UHS-I and HS200 features, he must provide
; an independent power supply for the card. This is only used in platforms
; that supports SD3.0 cards and eMMC4.4+ flashes
;-------------------------------------------------------------------------------
[mmc0_para]
sdc_used = 1
sdc_detmode = 2
sdc_buswidth = 4
sdc_d1 = port:PF00<2><1><2><default>
sdc_d0 = port:PF01<2><1><2><default>
sdc_clk = port:PF02<2><1><2><default>
sdc_cmd = port:PF03<2><1><2><default>
sdc_d3 = port:PF04<2><1><2><default>
sdc_d2 = port:PF05<2><1><2><default>
sdc_det = port:PB04<4><1><2><default>
sdc_use_wp = 0
sdc_wp =
sdc_isio = 0
sdc_regulator = "none"

[mmc1_para]
sdc_used = 1
sdc_detmode = 4
sdc_buswidth = 4
sdc_clk = port:PG00<2><1><1><default>
sdc_cmd = port:PG01<2><1><1><default>
sdc_d0 = port:PG02<2><1><1><default>
sdc_d1 = port:PG03<2><1><1><default>
sdc_d2 = port:PG04<2><1><1><default>
sdc_d3 = port:PG05<2><1><1><default>
sdc_det =
sdc_use_wp = 0
sdc_wp =
sdc_isio = 1
sdc_regulator = "none"

[mmc2_para]
sdc_used = 0
sdc_detmode = 3
sdc_buswidth = 8
sdc_clk = port:PC05<3><1><2><default>
sdc_cmd = port:PC06<3><1><2><default>
sdc_d0 = port:PC08<3><1><2><default>
sdc_d1 = port:PC09<3><1><2><default>
sdc_d2 = port:PC10<3><1><2><default>
sdc_d3 = port:PC11<3><1><2><default>
sdc_d4 = port:PC12<3><1><2><default>
sdc_d5 = port:PC13<3><1><2><default>
sdc_d6 = port:PC14<3><1><2><default>
sdc_d7 = port:PC15<3><1><2><default>
emmc_rst = port:PC16<3><1><2><default>
sdc_det =
sdc_use_wp = 0
sdc_wp =
sdc_isio = 0
sdc_regulator = "none"

;----------------------------------------------------------------------------------
;usb configuration
;usb_used: usb controller enable, 0-disable, 1-enable
;usb_port_type: usb mode: 0-device, 1-host, 2-otg
;usb_detect_type: usb hotplug detect mode, 0-none, 1-vbus/id detect, 2-id/dpdm detect
;usb_id_gpio: usb id detect IO
;usb_det_vbus_gpio: usb vbus detect IO, "axp_ctrl" for axp
;usb_drv_vbus_gpio: usb dirve vbus IO
;usb_restrict_gpio: usb current restrict IO
;usb_restric_flag: usb current restrict flag
;----------------------------------------------------------------------------------
[usbc0]
usb_used = 1
usb_port_type = 2
usb_detect_type = 1
usb_id_gpio = port:PH8<0><1><default><default>
usb_det_vbus_gpio = "axp_ctrl"
usb_drv_vbus_gpio = port:power4<1><0><default><0>
usb_restrict_gpio =
usb_host_init_state = 0
usb_restric_flag = 0
usb_restric_voltage = 3550000
usb_restric_capacity= 5

[usbc1]
usb_used = 1
usb_port_type = 1
usb_detect_type = 0
usb_id_gpio =
usb_det_vbus_gpio =
usb_drv_vbus_gpio =
usb_restrict_gpio =
usb_host_init_state = 0
usb_restric_flag = 0


;----------------------------------------------------------------------------------

; USB Device vendor Info.
;----------------------------------------------------------------------------------
[usb_feature]
vendor_id = 0x1F3A
mass_storage_id = 0x1000
adb_id = 0x1001

manufacturer_name = "USB Developer"
product_name = "Android"
serial_number = "20080411"

[msc_feature]
vendor_name = "USB 2.0"
product_name = "USB Flash Driver"
release = 100
luns = 2

;--------------------------------------------------------------------------------
; G sensor configuration
; gs_twi_id --- TWI ID for controlling Gsensor (0: TWI0, 1: TWI1, 2: TWI2)
;--------------------------------------------------------------------------------
[gsensor_para]
gsensor_used = 1
gsensor_twi_id = 1
gsensor_twi_addr = 0x18
gsensor_int1 =
gsensor_int2 =

;--------------------------------------------------------------------------------
; G sensor automatic detection configuration
;gsensor_detect_used --- Whether startup automatic inspection function. 1:used,0:unused
;Module name postposition 1 said detection, 0 means no detection.
;--------------------------------------------------------------------------------
[gsensor_list_para]
gsensor_det_used = 1
bma250 = 0
stk831x = 1
mma8452 = 0
mma7660 = 1
mma865x = 1
afa750 = 0
lis3de_acc = 0
lis3dh_acc = 0
kxtik = 0
dmard10 = 0
dmard06 = 1
mxc622x = 1
fxos8700 = 0
lsm303d = 0
mc32x0 = 1
;--------------------------------------------------------------------------------
; gps gpio configuration
; gps_spi_id: the index of SPI controller. 0: SPI0, 1: SPI1, 2: SPI2, 15: no SPI used
; gps_spi_cs_num: the chip select number of SPI controller. 0: SPI CS0, 1: SPI CS1
; gps_lradc: the lradc number for GPS used. 0 and 1 is valid, set 2 if not use lradc
;--------------------------------------------------------------------------------
[gps_para]

;--------------------------------------------------------------------------------
;wifi configuration
;wifi_sdc_id: 0- SDC0, 1- SDC1, 2- SDC2, 3- SDC3
;wifi_usbc_id: 0- USB0, 1- USB1, 2- USB2
;wifi_usbc_type: 1- EHCI(speed 2.0), 2- OHCI(speed 1.0)
;wifi_mod_sel: 0- none, 1- ap6181, 2- ap6210(wifi+bt),
; 3 - rtl8188eu, 4- rtl8723au(wifi+bt)
;--------------------------------------------------------------------------------
[wifi_para]
;----------------------------rtl8188etv---------------------------
;wifi_used = 1
;wifi_sdc_id = 0
;wifi_usbc_id = 1
;wifi_usbc_type = 1
;wifi_mod_sel = 3
;wifi_power = "axp22_dldo1"
;----------------------------rtl8189etv---------------------------
wifi_used = 1
wifi_sdc_id = 1
wifi_usbc_id = 1
wifi_usbc_type = 1
wifi_mod_sel = 6
wifi_power = "axp22_dldo1"
wifi_power_ext1 = ""
wifi_power_ext2 = ""
rtl8189es_shdn = port:PL06<1><default><default><0>
rtl8189es_host_wake = port:PL07<4><default><default><1>
;------------------------------end--------------------------------

; 1 - ap6181 sdio wifi gpio config
;ap6xxx_wl_regon = port:PL06<1><default><default><0>
;ap6xxx_wl_host_wake = port:PL07<4><default><default><0>

; 2 - ap6210 sdio wifi gpio config
;ap6xxx_wl_regon = port:PL06<1><default><default><0>
;ap6xxx_wl_host_wake = port:PL07<4><default><default><0>
;ap6xxx_bt_regon = port:PL08<1><default><default><0>
;ap6xxx_bt_wake = port:PL10<1><default><default><0>
;ap6xxx_bt_host_wake = port:PL09<4><default><default><0>

; 3 - rtl8188eu usb wifi gpio conifg

; 4 - rtl8723au usb wifi + bt

;--------------------------------------------------------------------------------
;blue tooth
;bt_used ---- blue tooth used (0- no used, 1- used)
;bt_uard_id ---- uart index
;--------------------------------------------------------------------------------
[bt_para]
bt_used = 0
bt_uart_id = 1

;--------------------------------------------------------------------------------
;3G configuration
;--------------------------------------------------------------------------------
[3g_para]
3g_used = 1
3g_usbc_num =
3g_uart_num = 2
bb_name = "gm530"
bb_vbat =
bb_on =
bb_pwr_on = port:PL03<1><default><default><0>
bb_wake = port:PL04<1><default><default><0>
bb_rf_dis =
bb_rst = port:PL05<1><default><default><0>
bb_dldo = ""
bb_dldo_min_uV = 2800000
bb_dldo_max_uV = 2800000

bb_wake_ap = port:PL02<4><default><default><0>

;--------------------------------------------------------------------------------
;2G configuration
;--------------------------------------------------------------------------------
[2g_para]
2g_used = 0
bb_pwr_on = port:PL03<1><default><default><0>
;bb_wake = port:PL04<1><default><default><0>
bb_rst = port:PL05<1><default><default><0>

;--------------------------------------------------------------------------------
;gyroscope
;--------------------------------------------------------------------------------
[gy_para]
gy_used = 0
gy_twi_id = 1
gy_twi_addr = 0x6a
gy_int1 =
gy_int2 =

;--------------------------------------------------------------------------------
; Gyro automatic detection configuration
;gy_detect_used --- Whether startup automatic inspection function. 1:used,0:unused
;Module name postposition 1 said detection, 0 means no detection.
;--------------------------------------------------------------------------------
[gy_list_para]
gy_det_used = 1
l3gd20_gyr = 1

;--------------------------------------------------------------------------------
;light sensor
;--------------------------------------------------------------------------------
[ls_para]
ls_used = 0
ls_twi_id = 1
ls_twi_addr = 0x23
ls_int = port:PB07<4><1><default><default>

;--------------------------------------------------------------------------------
; lsensor automatic detection configuration
;ls_detect_used --- Whether startup automatic inspection function. 1:used,0:unused
;Module name postposition 1 said detection, 0 means no detection.
;--------------------------------------------------------------------------------
[ls_list_para]
ls_det_used = 1
ltr_501als = 1
jsa1212 = 1
;--------------------------------------------------------------------------------
;compass
;--------------------------------------------------------------------------------
[compass_para]
compass_used = 0
compass_twi_id = 1
compass_twi_addr = 0x0d
compass_int =

;--------------------------------------------------------------------------------
;i2s_master:1: SND_SOC_DAIFMT_CBM_CFM(codec clk & FRM master) use
; 2: SND_SOC_DAIFMT_CBS_CFM(codec clk slave & FRM master) not use
; 3: SND_SOC_DAIFMT_CBM_CFS(codec clk master & frame slave) not use
; 4: SND_SOC_DAIFMT_CBS_CFS(codec clk & FRM slave) use
;i2s_select:0 is pcm.1 is i2s
;audio_format: 1:SND_SOC_DAIFMT_I2S(standard i2s format). use
; 2:SND_SOC_DAIFMT_RIGHT_J(right justfied format).
; 3:SND_SOC_DAIFMT_LEFT_J(left justfied format)
; 4:SND_SOC_DAIFMT_DSP_A(pcm. MSB is available on 2nd BCLK rising edge after LRC rising edge). use
; 5:SND_SOC_DAIFMT_DSP_B(pcm. MSB is available on 1nd BCLK rising edge after LRC rising edge)
;signal_inversion:1:SND_SOC_DAIFMT_NB_NF(normal bit clock + frame) use
; 2:SND_SOC_DAIFMT_NB_IF(normal BCLK + inv FRM)
; 3:SND_SOC_DAIFMT_IB_NF(invert BCLK + nor FRM) use
; 4:SND_SOC_DAIFMT_IB_IF(invert BCLK + FRM)
;over_sample_rate: support 128fs/192fs/256fs/384fs/512fs/768fs
;sample_resolution :16bits/20bits/24bits
;word_select_size :16bits/20bits/24bits/32bits
;pcm_sync_period :16/32/64/128/256
;msb_lsb_first :0: msb first; 1: lsb first
;sign_extend :0: zero pending; 1: sign extend
;slot_index :slot index: 0: the 1st slot - 3: the 4th slot
;slot_width :8 bit width / 16 bit width
;frame_width :0: long frame = 2 clock width; 1: short frame
;tx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law
;rx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law
;--------------------------------------------------------------------------------
[i2s0]
i2s_used = 0
i2s_channel = 2
i2s_master = 1
i2s_select = 0
audio_format = 4
signal_inversion = 3
over_sample_rate = 256
sample_resolution = 16
word_select_size = 32
pcm_sync_period = 256
msb_lsb_first = 0
sign_extend = 0
slot_index = 0
slot_width = 16
frame_width = 1
tx_data_mode = 0
rx_data_mode = 0
i2s_mclk =
i2s_bclk = port:PB04<2><1><default><default>
i2s_lrclk = port:PB05<2><1><default><default>
i2s_dout0 = port:PB06<2><1><default><default>
i2s_dout1 =
i2s_dout2 =
i2s_dout3 =
i2s_din = port:PB07<2><1><default><default>

;--------------------------------------------------------------------------------
;pcm_master:1: SND_SOC_DAIFMT_CBM_CFM(codec clk & FRM master) use
; 2: SND_SOC_DAIFMT_CBS_CFM(codec clk slave & FRM master) not use
; 3: SND_SOC_DAIFMT_CBM_CFS(codec clk master & frame slave) not use
; 4: SND_SOC_DAIFMT_CBS_CFS(codec clk & FRM slave) use
;pcm_select:1 is pcm.0 is i2s
;audio_format: 1:SND_SOC_DAIFMT_I2S(standard i2s format). use
; 2:SND_SOC_DAIFMT_RIGHT_J(right justfied format).
; 3:SND_SOC_DAIFMT_LEFT_J(left justfied format)
; 4:SND_SOC_DAIFMT_DSP_A(pcm. MSB is available on 2nd BCLK rising edge after LRC rising edge). use
; 5:SND_SOC_DAIFMT_DSP_B(pcm. MSB is available on 1nd BCLK rising edge after LRC rising edge)
;signal_inversion:1:SND_SOC_DAIFMT_NB_NF(normal bit clock + frame) use
; 2:SND_SOC_DAIFMT_NB_IF(normal BCLK + inv FRM)
; 3:SND_SOC_DAIFMT_IB_NF(invert BCLK + nor FRM) use
; 4:SND_SOC_DAIFMT_IB_IF(invert BCLK + FRM)
;over_sample_rate: support 128fs/192fs/256fs/384fs/512fs/768fs
;sample_resolution :16bits/20bits/24bits
;word_select_size :16bits/20bits/24bits/32bits
;pcm_sync_period :16/32/64/128/256
;msb_lsb_first :0: msb first; 1: lsb first
;sign_extend :0: zero pending; 1: sign extend
;slot_index :slot index: 0: the 1st slot - 3: the 4th slot
;slot_width :8 bit width / 16 bit width
;frame_width :0: long frame = 2 clock width; 1: short frame
;tx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law
;rx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law
;--------------------------------------------------------------------------------
[i2s1]
pcm_used = 0
pcm_channel = 2
pcm_master = 4
pcm_select = 1
audio_format = 4
signal_inversion = 3
over_sample_rate = 512
sample_resolution = 16
word_select_size = 32
pcm_sync_period = 64
msb_lsb_first = 0
sign_extend = 0
slot_index = 0
slot_width = 16
frame_width = 1
tx_data_mode = 0
rx_data_mode = 0
pcm_mclk =
pcm_bclk = port:PD14<3><1><default><default>
pcm_lrclk = port:PD15<3><1><default><default>
pcm_dout = port:PD16<3><1><default><default>
pcm_din = port:PD17<3><1><default><default>

;--------------------------------------------------------------------------------
;pa_single_vol,pa_double_vol: 31 level,1.5db/step.0x1f is the large volume.
;cap_vol:use for system record,0x0--0db,0x1--24db,0x2--27db,0x3--30db,0x4--33db,0x5--36db,0x6--39db,0x7--42db
;headphone_vol,earpiece_vol: must least than 0x3b. 0x1 is a step.
;headset_mic_vol: headset mic(mic2) vol,use for phone headset mic call
;main_mic_vol: main mic(mic1) vol,use for phone main mic call
;--------------------------------------------------------------------------------
[audio0]
audio_used = 1
audio_hp_ldo = "none"
headphone_vol = 0x3b
earpiece_vol = 0x3b
cap_vol = 0x5
pa_single_vol = 0x3a
pa_double_used = 0
pa_double_vol = 0x3e
headphone_direct_used = 0
audio_pa_ctrl = port:PH09<1><default><default><0>
headphone_mute_used = 0
audio_mute_ctrl =
headset_mic_vol = 3
main_mic_vol = 3

;-------------------------------------------------------------------------------------
;pmu_used ---0:not used,1:used
;pmu_twi_addr ---slave address
;pmu_twi_id ---i2c bus number (0 TWI0, 1 TWI2, 2 TWI3)
;pmu_irq_id ---irq number (0 irq0,1 irq1,……)
;pmu_battery_rdc ---battery initial resistance
;pmu_battery_cap ---battery capability,mAh
;pmu_batdeten ---battery detect en;0:disable 1:enable
;pmu_runtime_chgcur ---set initial charging current limite,mA，300/450/600/750/900/1050/1200/1350/1500/1650/1800/1950/
;pmu_earlysuspend_chgcur ---set earlysuspend charging current limite,mA，300/450/600/750/900/1050/1200/1350/1500/1650/1800/1950/
;pmu_suspend_chgcur ---set suspend charging current limite,mA，300/450/600/750/900/1050/1200/1350/1500/1650/1800/1950/
;pmu_shutdown_chgcur ---set shutdown charging current limite,mA，300/450/600/750/900/1050/1200/1350/1500/1650/1800/1950/
;pmu_init_chgvol ---set initial charing target voltage,mV,4100/4220/4200/4240
;pmu_init_chgend_rate ---set initial charing end current rate,10/15
;pmu_init_chg_enabled ---set initial charing enabled,0:disable,1:enable
;pmu_init_adc_freq ---set initial adc frequency,Hz,100/200/400/800
;pmu_init_adcts_freq ---set initial adc TS,Hz,100/200/400/800
;pmu_init_chg_pretime ---set initial pre-charging time,min,40/50/60/70
;pmu_init_chg_csttime ---set initial constance-charging time,min,360/480/600/720
;pmu_batt_cap_correct ---correct the battery capacity or not when one charge cycle 0:not correct 1:correct
;pmu_bat_regu_en ---bat regulator is enable or not when charge done 0:disable 1:enable
;pmu_bat_para1 ---battery indication at 3.13V
;pmu_bat_para2 ---battery indication at 3.27V
;pmu_bat_para3 ---battery indication at 3.34V
;pmu_bat_para4 ---battery indication at 3.41V
;pmu_bat_para5 ---battery indication at 3.48V
;pmu_bat_para6 ---battery indication at 3.52V
;pmu_bat_para7 ---battery indication at 3.55V
;pmu_bat_para8 ---battery indication at 3.57V
;pmu_bat_para9 ---battery indication at 3.59V
;pmu_bat_para10 ---battery indication at 3.61V
;pmu_bat_para11 ---battery indication at 3.63V
;pmu_bat_para12 ---battery indication at 3.64V
;pmu_bat_para13 ---battery indication at 3.66V
;pmu_bat_para14 ---battery indication at 3.7V
;pmu_bat_para15 ---battery indication at 3.73V
;pmu_bat_para16 ---battery indication at 3.77V
;pmu_bat_para17 ---battery indication at 3.78V
;pmu_bat_para18 ---battery indication at 3.8V
;pmu_bat_para19 ---battery indication at 3.82V
;pmu_bat_para20 ---battery indication at 3.84V
;pmu_bat_para21 ---battery indication at 3.85V
;pmu_bat_para22 ---battery indication at 3.87V
;pmu_bat_para23 ---battery indication at 3.91V
;pmu_bat_para24 ---battery indication at 3.94V
;pmu_bat_para25 ---battery indication at 3.98V
;pmu_bat_para26 ---battery indication at 4.01V
;pmu_bat_para27 ---battery indication at 4.05V
;pmu_bat_para28 ---battery indication at 4.08V
;pmu_bat_para29 ---battery indication at 4.1V
;pmu_bat_para30 ---battery indication at 4.12V
;pmu_bat_para31 ---battery indication at 4.14V
;pmu_bat_para32 ---battery indication at 4.15V
;pmu_usbvol_limit ---set usb-ac limited voltage enable,1:enable，0：disable
;pmu_usbcur_limit ---set usb-ac limited current enable,1:enable，0：disable
;pmu_usbvol ---set usb-ac limited voltage level,mV,4000/4100/4200/4300/4400/4500/4600/4700,0 - not limite
;pmu_usbcur ---set usb-ac limited current level,mA,500/900, 0 - not limite
;pmu_usbvol_pc ---set usb-pc limited voltage level,mV,4000/4100/4200/4300/4400/4500/4600/4700,0 - not limite
;pmu_usbcur_pc ---set usb-pc limited current level,mA,500/900, 0 - not limite
;pmu_pwroff_vol ---set protect voltage when system start up,mV,2600/2700/2800/2900/3000/3100/3200/3300
;pmu_pwron_vol ---set protect voltage after system start up,mV,2600/2700/2800/2900/3000/3100/3200/3300
;pmu_pekoff_time ---set pek off time,ms, 4000/6000/8000/10000
;pmu_pekoff_func ---set pek off func, 0:shutdown,1:restart
;pmu_pekoff_en ---set pek offlevel powerdown or not, 0:not powerdown,1:powerdown
;pmu_peklong_time ---set pek pek long irq time,ms,1000/1500/2000/2500
;pmu_pekon_time ---set pek on time,ms,128/1000/2000/3000
;pmu_pwrok_time ---set pmu pwrok delay time,ms,8/16/32/64
;pmu_battery_warning_level1 ---low power warning high level,5%-20%,1%/step
;pmu_battery_warning_level2 ---low power warning low level,0%-15%,1%/step
;pmu_restvol_time ---battery indicaton reflash time,30/60/120/
;pmu_ocv_cou_adjust_time ---ocv battery indication reflash time,60/120/30
;pmu_chgled_func ---CHGKED pin control，0:controlled by pmu,1:controlled by Charger
;pmu_chgled_type ---CHGLED Type select when pmu_chgled_func=0,0:Type A，1：Type B
;pmu_vbusen_func ---N_VBUSEN function select,0:as an output,1:as an input
;pmu_reset ---when power key press longer than 16's,PMU reset or not.0:not reset 1:reset
;pmu_IRQ_wakeup ---press IRQ wakeup or not when sleep or power down.0:not wakeup 1:wakeup
;pmu_hot_shutdowm ---when PMU over temperature protect or not;0:disable 1:enable
;pmu_inshort ---ACIN and VBUS inshort or not by software;0:auto detect 1:inshort
;--------------------------------------------------------------------------------------------------------
[pmu1_para]
pmu_used = 1
pmu_twi_addr = 0x34
pmu_twi_id = 1
pmu_irq_id = 0
pmu_battery_rdc = 168
;pmu_battery_cap = 2850
pmu_battery_cap = 2350
pmu_batdeten = 1
pmu_runtime_chgcur = 900
pmu_earlysuspend_chgcur = 900
pmu_suspend_chgcur = 1500
pmu_shutdown_chgcur = 1500
pmu_init_chgvol = 4200
pmu_init_chgend_rate = 15
pmu_init_chg_enabled = 1
pmu_init_adc_freq = 800
pmu_init_adcts_freq = 800
pmu_init_chg_pretime = 70
pmu_init_chg_csttime = 720
pmu_batt_cap_correct = 1
pmu_bat_regu_en = 0

pmu_bat_para1 = 0
pmu_bat_para2 = 0
pmu_bat_para3 = 0
pmu_bat_para4 = 0
pmu_bat_para5 = 0
pmu_bat_para6 = 0
pmu_bat_para7 = 0
pmu_bat_para8 = 0
pmu_bat_para9 = 3
pmu_bat_para10 = 4
pmu_bat_para11 = 4
pmu_bat_para12 = 5
pmu_bat_para13 = 6
pmu_bat_para14 = 14
pmu_bat_para15 = 18
pmu_bat_para16 = 31
pmu_bat_para17 = 36
pmu_bat_para18 = 41
pmu_bat_para19 = 48
pmu_bat_para20 = 53
pmu_bat_para21 = 55
pmu_bat_para22 = 58
pmu_bat_para23 = 64
pmu_bat_para24 = 69
pmu_bat_para25 = 74
pmu_bat_para26 = 78
pmu_bat_para27 = 81
pmu_bat_para28 = 85
pmu_bat_para29 = 88
pmu_bat_para30 = 92
pmu_bat_para31 = 95
pmu_bat_para32 = 100

pmu_usbvol_limit = 0
pmu_usbcur_limit = 0
pmu_usbvol = 4000
pmu_usbcur = 0
pmu_usbvol_pc = 4400
pmu_usbcur_pc = 500
pmu_pwroff_vol = 3300
pmu_pwron_vol = 2900
pmu_pekoff_time = 6000
pmu_pekoff_func = 0
pmu_pekoff_en = 1
pmu_peklong_time = 1500
pmu_pekon_time = 1000
pmu_pwrok_time = 64
pmu_battery_warning_level1 = 14
pmu_battery_warning_level2 = 0
pmu_restvol_adjust_time = 60
pmu_ocv_cou_adjust_time = 60
pmu_chgled_func = 0
pmu_chgled_type = 0
pmu_vbusen_func = 1
pmu_reset = 0
pmu_IRQ_wakeup = 1
pmu_hot_shutdowm = 1
pmu_inshort = 0
power_start = 0

[pmu2_para]
pmu_used = 0
pmu_twi_addr = 0x34
pmu_twi_id = 1
pmu_irq_id = 1

;----------------------------------------------------------------------------------
; dvfs voltage-frequency table configuration
;
; extremity_freq(Hz): cpu extremity frequency when run benckmark or demo apk
; 1536MHz@1500mV with radiator, 1248MHz@1260mV without radiator
; max_freq: cpu maximum frequency, based on Hz, can not be more than 1008MHz
; min_freq: cpu minimum frequency, based on Hz, can not be less than 96MHz
;
; LV_count: count of LV_freq/LV_volt, must be < 16
;
; LV1: core vdd is 1.30v if cpu frequency is (1104Mhz, 1200Mhz]
; LV2: core vdd is 1.20v if cpu frequency is (1008Mhz, 1104Mhz]
; LV3: core vdd is 1.10v if cpu frequency is (816Mhz, 1008Mhz]
; LV4: core vdd is 1.00v if cpu frequency is (600Mhz, 816Mhz]
; LV5: core vdd is 0.90v if cpu frequency is (0Mhz, 600Mhz]
; LV6: core vdd is 0.90v if cpu frequency is (0Mhz, 600Mhz]
; LV7: core vdd is 0.90v if cpu frequency is (0Mhz, 600Mhz]
; LV8: core vdd is 0.90v if cpu frequency is (0Mhz, 600Mhz]
;
;----------------------------------------------------------------------------------
[dvfs_table]
extremity_freq = 1200000000
max_freq = 1200000000
min_freq = 60000000

LV_count = 8

LV1_freq = 1536000000
LV1_volt = 1500

LV2_freq = 1296000000
LV2_volt = 1340

LV3_freq = 1200000000
LV3_volt = 1240

LV4_freq = 1008000000
LV4_volt = 1140

LV5_freq = 816000000
LV5_volt = 1040

;LV6_freq = 600000000
;LV6_volt = 900
LV6_freq = 312000000
LV6_volt = 960

LV7_freq = 0
;LV7_volt = 900
LV7_volt = 960

LV8_freq = 0
;LV8_volt = 900
LV8_volt = 960



;----------------------------------------------------------------------------------
;virtual device
;virtual device for pinctrl testing
;device have pin PA1 PA2
;----------------------------------------------------------------------------------
[Vdevice]
Vdevice_used = 1
Vdevice_0 = port:PA01<5><1><2><default>
Vdevice_1 = port:PA02<5><1><2><default>

;----------------------------------------------------------------------------------
;s_uart0 config parameters
;s_uart_used --s_uart0 whether used for arisc debugging
;----------------------------------------------------------------------------------
[s_uart0]
s_uart_used = 0
s_uart_tx = port:PL02<2><default><default><default>
s_uart_rx = port:PL03<2><default><default><default>

;----------------------------------------------------------------------------------
;s_rsb0 config parameters
;s_rsb_used --s_rsb0 whether used for arisc
;----------------------------------------------------------------------------------
[s_rsb0]
s_rsb_used = 1
s_rsb_sck = port:PL00<2><1><2><default>
s_rsb_sda = port:PL01<2><1><2><default>

[mali_para]
mali_used = 1
mali_clkdiv = 1
mali_extreme_freq = 408
mali_extreme_vol = 1100


;----------------------------------------------------------------------------------
; dram dvfs voltage-frequency table configuration
;
; LV_count: count of LV_freq/LV_volt
;
; LV1: core vdd is 1.1v if dram frequency is (360Mhz, 552Mhz]
; LV2: core vdd is 1.0v if dram frequency is ( 0Mhz, 360Mhz]
; LV3: core vdd is 1.0v if dram frequency is ( 0Mhz, 360Mhz]
;
;----------------------------------------------------------------------------------
[dram_dvfs_table]
LV_count = 3

LV1_freq = 552000000
LV1_volt = 1100

LV2_freq = 360000000
LV2_volt = 1000

LV3_freq = 0
LV3_volt = 1000

[redhaos]

Blaze,можно поставить прошивку через отг, с usb флэшки???