Прошивка планшетов на AllWinner A10 и A13

Инструкции для КПК (PPC)

Модератор: чипега

zekagzel
Начинающий
Начинающий
Сообщения: 1
Зарегистрирован: 23.08.2017 1:27

Прошивка планшетов на AllWinner A10 и A13

Непрочитанное сообщение#5131 » zekagzel » 23.08.2017 1:57

Добрый день,помогите пожалуйста с прошивкой telefunken tf-mid 9701g,процессор а10 с9023са 6В51 тачскрин PINGBO PB97DR8118 NB. На материнке нашел только это: 2#3GBF-V032012-10-27.А это по-моему радиомодуль:HWM630 SW VER:C1B2106. Заводская прошивка с 4PDA глючит без конца,от RMD 1050 не пробовал потому что пишут что много багов.Если кто-то имел дело с этим зверем подскажите пожалуйста может есть какая-то еще прошивка,кстати диагональ 9.7,если что.

vrt
Начинающий
Начинающий
Сообщения: 1
Зарегистрирован: 28.08.2017 13:58

Прошивка планшетов на AllWinner A10 и A13

Непрочитанное сообщение#5132 » vrt » 28.08.2017 14:07

Помогите с прошивкой Lark Freeme 10.25.
Процессор- A13 D1143CA
Материнка- INET-98VB-REV01
Тач-IVO 090 REV.1 B13042311078

freg57
Начинающий
Начинающий
Сообщения: 2
Зарегистрирован: 03.09.2017 21:14

Прошивка планшетов на AllWinner A10 и A13

Непрочитанное сообщение#5133 » freg57 » 04.09.2017 8:25

Доброе утро, форумчане!
После замены тача на Apache A97 - на экране только загрузочная надпись "Андроид" и фсе ((. Переплыл океан инета в обе стороны - нигде не нашел прошивки под этого китайца. Помогите, плиз, кто чем может ))
На плате:
Topwice A106G - mainboard- V1.2.0 36.12
FM E351308
94V-0
В сервисный режим (китайские иероглифы) входит и рисует вот такое: A106_V1.0.3_20120913_r293+34-668efe5
Спасибо, добрые люди!

Dr_Wolodya
Начинающий
Начинающий
Сообщения: 1
Зарегистрирован: 05.09.2017 20:45

Прошивка планшетов на AllWinner A10 и A13

Непрочитанное сообщение#5134 » Dr_Wolodya » 05.09.2017 20:54

Blaze писал(а):
16.09.2013 19:34
GOCLEVER TAB A 103
Android 4.0.3 от 12.04.2012 (only for GCA1031202xxxx and GCA10312031001 - GCA10312032000): GCA103_120331_ICS.zip
Android 4.0.3 от 07.05.2012 (only for GCA10312032001 - GCA10312032600): GCA103_120419bc_ICS.zip
Android 4.0.3 от 10.05.2012 (only for GCA10312032601-GCA10312034000; GCA1031204xxxx; GCA1031205xxxx; GCA1031206xxxx): GCA103_120428_c2.zip
Android 4.0.4 от 28.09.2012 (only for GCTA1031207xxxx, GCTA1031208xxxx, GCTA1031209xxxx): GCA103_120824x.zip
Android 4.0.4 от 28.09.2012 (only for GCA10312032601 to GCA10312034000; GCA1031204xxxx; GCA1031205xxxx; GCA1031206xxxx): GCA103_120830.zip
Переложите пожалуйста прошивку Android 4.0.4 от 28.09.2012 (only for GCTA1031207xxxx, GCTA1031208xxxx, GCTA1031209xxxx): GCA103_120824x.zip.
Нужно для восстановления next wolf viewtopic.php?p=15020#p15020.
Спасибо

dadaduda
Начинающий
Начинающий
Сообщения: 8
Зарегистрирован: 25.06.2016 14:30
Откуда: Игарка

Прошивка планшетов на AllWinner A10 и A13

Непрочитанное сообщение#5135 » dadaduda » 15.09.2017 8:55

Здравствуйте.Планшеткитаец Самсунг P5200
мать-AL-A13-90A 4GB CPT ETV 250 E SN:13100556-01 REV:3.02012.12.14
ЧИП A 13 D 9078CA 1AC1
Кто то может сказать что это за резистор или как там,по моему он сгорел?
Извиняюсь конечно за фото
Последний раз редактировалось dadaduda 23.09.2017 14:24, всего редактировалось 1 раз.

Аватара пользователя
Grey
Начинающий
Начинающий
Сообщения: 2
Зарегистрирован: 16.09.2017 13:25

Прошивка планшетов на AllWinner A10 и A13

Непрочитанное сообщение#5136 » Grey » 16.09.2017 13:44

Доброго времени суток! Есть ли у кого нибудь script.fex для Китайского 8" "тачскрина" ?
Зеркальность исправил changexy.cmd, а вот отступ касания никак!

Интересуют показатели:

Код: Выделить всё

[gsensor_para]
gsensor_used = 
gsensor_unuse_name =
gsensor_twi_id = 
gsensor_twi_addr =
gsensor_int1 =
gsensor_int2 =
gsensor_direct_x =
gsensor_direct_y =
gsensor_direct_z =
gsensor_xy_revert =
Подопытный:
Impression ImPad 7213 8", 800x480
Число пикселей на дюйм (PPI):117
Процессор:Allwinner/BoxChip A13 1000 МГц
Android 4.0.4

Слитый .fex после changexy.cmd :

Код: Выделить всё

[product]
version = "1.0"
machine = "A13-EVB-V1.0"

[target]
boot_clock = 1008
dcdc2_vol = 1400
dcdc3_vol = 1200
ldo2_vol = 3000
ldo3_vol = 3300
ldo4_vol = 3300
pll4_freq = 960
pll6_freq = 720
power_start = 0
storage_type = 0

[card_boot]
logical_start = 40960
sprite_gpio0 =

[pm_para]
standby_mode = 0

[card_boot0_para]
card_ctrl = 0
card_high_speed = 1
card_line = 4
sdc_d1 = port:PF00<2><1><default><default>
sdc_d0 = port:PF01<2><1><default><default>
sdc_clk = port:PF02<2><1><default><default>
sdc_cmd = port:PF03<2><1><default><default>
sdc_d3 = port:PF04<2><1><default><default>
sdc_d2 = port:PF05<2><1><default><default>

[twi_para]
twi_port = 0
twi_scl = port:PB00<2><1><default><default>
twi_sda = port:PB01<2><1><default><default>

[uart_para]
uart_debug_port = 0
uart_debug_tx = port:PG03<4><1><default><default>
uart_debug_rx = port:PG04<4><1><default><default>

[jtag_para]
jtag_enable = 0
jtag_ms = port:PF00<4><1><default><default>
jtag_ck = port:PF05<4><1><default><default>
jtag_do = port:PF03<4><1><default><default>
jtag_di = port:PF01<4><1><default><default>

[dram_para]
dram_baseaddr = 0x40000000
dram_clk = 432
dram_type = 3
dram_rank_num = 1
dram_chip_density = 2048
dram_io_width = 8
dram_bus_width = 16
dram_cas = 9
dram_zq = 0x7b
dram_odt_en = 0
dram_size = 512
dram_tpr0 = 0x42d899b7
dram_tpr1 = 0xa090
dram_tpr2 = 0x22a00
dram_tpr3 = 0x0
dram_tpr4 = 0x0
dram_tpr5 = 0x0
dram_emr1 = 0x4
dram_emr2 = 0x10
dram_emr3 = 0x0

[nand_para]
nand_used = 1
nand_we = port:PC00<2><default><default><default>
nand_ale = port:PC01<2><default><default><default>
nand_cle = port:PC02<2><default><default><default>
nand_ce1 = port:PC03<2><default><default><default>
nand_ce0 = port:PC04<2><default><default><default>
nand_nre = port:PC05<2><default><default><default>
nand_rb0 = port:PC06<2><default><default><default>
nand_rb1 = port:PC07<2><default><default><default>
nand_d0 = port:PC08<2><default><default><default>
nand_d1 = port:PC09<2><default><default><default>
nand_d2 = port:PC10<2><default><default><default>
nand_d3 = port:PC11<2><default><default><default>
nand_d4 = port:PC12<2><default><default><default>
nand_d5 = port:PC13<2><default><default><default>
nand_d6 = port:PC14<2><default><default><default>
nand_d7 = port:PC15<2><default><default><default>
nand_wp =
nand_ce2 =
nand_ce3 =
nand_ce4 =
nand_ce5 =
nand_ce6 =
nand_ce7 =
nand_spi =
nand_ndqs = port:PC19<2><default><default><default>
good_block_ratio = 0

[mali_para]
mali_used = 1
mali_clkdiv = 2

[twi0_para]
twi0_used = 1
twi0_scl = port:PB00<2><default><default><default>
twi0_sda = port:PB01<2><default><default><default>

[twi1_para]
twi1_used = 1
twi1_scl = port:PB15<2><default><default><default>
twi1_sda = port:PB16<2><default><default><default>

[twi2_para]
twi2_used = 1
twi2_scl = port:PB17<2><default><default><default>
twi2_sda = port:PB18<2><default><default><default>

[uart_para0]
uart_used = 0
uart_port = 0
uart_type = 2
uart_tx = port:PB19<2><1><default><default>
uart_rx = port:PB20<2><1><default><default>

[uart_para1]
uart_used = 0
uart_port = 1
uart_type = 2
uart_tx = port:PG03<4><1><default><default>
uart_rx = port:PG04<4><1><default><default>

[spi1_para]
spi_used = 0
spi_cs0 = port:PG09<2><default><default><default>
spi_cs1 = port:PG13<2><default><default><default>
spi_sclk = port:PG10<2><default><default><default>
spi_mosi = port:PG11<2><default><default><default>
spi_miso = port:PG12<2><default><default><default>

[spi2_para]
spi_used = 0
spi_cs0 = port:PE00<4><default><default><default>
spi_sclk = port:PE01<4><default><default><default>
spi_mosi = port:PB02<4><default><default><default>
spi_miso = port:PB03<4><default><default><default>

[rtp_para]
rtp_used = 0
rtp_screen_size = 5
rtp_regidity_level = 5
rtp_press_threshold_enable = 0
rtp_press_threshold = 0x1f40
rtp_sensitive_level = 0xf
rtp_exchange_x_y_flag = 0

[ctp_para]
ctp_boxchip_type = 2579
ctp_twi_id = 1
ctp_used = 1
ctp_name = "ft5x_ts"
ctp_twi_addr = 0x38
ctp1_used = 1
ctp1_name = "Goodix-TS"
ctp1_twi_addr = 85
ctp4_used = 1
ctp4_name = "zet622x-ts"
ctp4_twi_addr = 118
ctp5_used = 1
ctp5_name = "byd693x-ts"
ctp5_twi_addr = 82
ctp10_used = 1
ctp10_name = "pixcir_cxx"
ctp10_twi_addr = 92
ctp19_used = 1
ctp19_name = "elan_ts"
ctp19_twi_addr = 20
cpt_screen_rotate = 0
ctp_screen_max_x = 800
ctp_screen_max_y = 600
ctp_revert_x_flag = 1
ctp_revert_y_flag = 1
ctp_exchange_x_y_flag = 1
ctp_havekey = 1
ctp_int_port = port:PG11<6><default><default><default>
ctp_wakeup = port:PB03<1><default><default><1>
ctp_io_port = port:PG11<6><default><default><default>

[tkey_para]
tkey_used = 0
tkey_name = "hv_keypad"
tkey_twi_id = 2
tkey_twi_addr = 0x62
tkey_int =

[motor_para]
motor_used = 0
motor_shake =

[disp_init]
disp_init_enable = 1
disp_mode = 0
screen0_output_type = 1
screen0_output_mode = 4
screen1_output_type = 1
screen1_output_mode = 4
fb0_framebuffer_num = 2
fb0_format = 10
fb0_pixel_sequence = 0
fb0_scaler_mode_enable = 0
fb1_framebuffer_num = 2
fb1_format = 10
fb1_pixel_sequence = 0
fb1_scaler_mode_enable = 0

[lcd0_para]
lcd_used = 1
lcd_pwm_not_used = 0
lcd_pwm_ch = 0
lcd_pwm_freq = 10000
lcd_pwm_pol = 1
lcd_x = 800
lcd_y = 600
lcd_dclk_freq = 40
lcd_if = 0
lcd_hbp = 46
lcd_ht = 1055
lcd_vbp = 23
lcd_vt = 1270
lcd_hv_if = 0
lcd_hv_smode = 0
lcd_hv_s888_if = 0
lcd_hv_syuv_if = 0
lcd_hv_vspw = 0
lcd_hv_hspw = 0
lcd_lvds_ch = 0
lcd_lvds_mode = 0
lcd_lvds_bitwidth = 0
lcd_lvds_io_cross = 0
lcd_cpu_if = 0
lcd_frm = 1
lcd_io_cfg0 = 268435456
lcd_gamma_correction_en = 0
lcd_gamma_tbl_0 = 0x0
lcd_gamma_tbl_1 = 0x10101
lcd_gamma_tbl_255 = 0xffffff
lcd_bl_en_used = 1
lcd_bl_en = port:power1<1><0><default><1>
lcd_power_used = 1
lcd_power = port:power0<1><0><default><1>
lcd_pwm_used = 1
lcd_pwm = port:PB02<2><0><default><default>
lcd_gpio_0 =
lcd_gpio_1 =
lcd_gpio_2 =
lcd_gpio_3 =
lcdd0 = port:PD00<2><0><default><default>
lcdd1 = port:PD01<2><0><default><default>
lcdd2 = port:PD02<2><0><default><default>
lcdd3 = port:PD03<2><0><default><default>
lcdd4 = port:PD04<2><0><default><default>
lcdd5 = port:PD05<2><0><default><default>
lcdd6 = port:PD06<2><0><default><default>
lcdd7 = port:PD07<2><0><default><default>
lcdd8 = port:PD08<2><0><default><default>
lcdd9 = port:PD09<2><0><default><default>
lcdd10 = port:PD10<2><0><default><default>
lcdd11 = port:PD11<2><0><default><default>
lcdd12 = port:PD12<2><0><default><default>
lcdd13 = port:PD13<2><0><default><default>
lcdd14 = port:PD14<2><0><default><default>
lcdd15 = port:PD15<2><0><default><default>
lcdd16 = port:PD16<2><0><default><default>
lcdd17 = port:PD17<2><0><default><default>
lcdd18 = port:PD18<2><0><default><default>
lcdd19 = port:PD19<2><0><default><default>
lcdd20 = port:PD20<2><0><default><default>
lcdd21 = port:PD21<2><0><default><default>
lcdd22 = port:PD22<2><0><default><default>
lcdd23 = port:PD23<2><0><default><default>
lcdclk = port:PD24<2><0><default><default>
lcdde = port:PD25<2><0><default><default>
lcdhsync = port:PD26<2><0><default><default>
lcdvsync = port:PD27<2><0><default><default>

[tv_out_dac_para]
dac_used = 1
dac0_src = 0

[hdmi_para]
hdmi_used = 0

[csi0_para]
csi_used = 1
csi_mode = 0
csi_dev_qty = 2
csi_stby_mode = 1
csi_mname = "gc0308"
csi_twi_id = 2
csi_twi_addr = 0x42
csi_if = 0
csi_vflip = 0
csi_hflip = 0
csi_iovdd = ""
csi_avdd = ""
csi_dvdd = ""
csi_flash_pol = 1
csi_facing = 1
csi_mname_b = "gt2005"
csi_twi_id_b = 2
csi_twi_addr_b = 0x78
csi_if_b = 0
csi_vflip_b = 0
csi_hflip_b = 0
csi_iovdd_b = ""
csi_avdd_b = ""
csi_dvdd_b = ""
csi_flash_pol_b = 1
csi_facing_b = 0
csi_pck = port:PE00<3><default><default><default>
csi_ck = port:PE01<3><default><default><default>
csi_hsync = port:PE02<3><default><default><default>
csi_vsync = port:PE03<3><default><default><default>
csi_d0 = port:PE04<3><default><default><default>
csi_d1 = port:PE05<3><default><default><default>
csi_d2 = port:PE06<3><default><default><default>
csi_d3 = port:PE07<3><default><default><default>
csi_d4 = port:PE08<3><default><default><default>
csi_d5 = port:PE09<3><default><default><default>
csi_d6 = port:PE10<3><default><default><default>
csi_d7 = port:PE11<3><default><default><default>
csi_reset = port:power3<1><default><default><0>
csi_power_en = port:power2<1><default><default><1>
csi_stby = port:PB10<1><default><default><1>
csi_flash =
csi_af_en =
csi_reset_b = port:power3<1><default><default><0>
csi_power_en_b = port:power2<1><default><default><1>
csi_stby_b = port:PG03<1><default><default><1>
csi_flash_b =
csi_af_en_b =

[csi1_para]
csi_used = 0
csi_mode = 0
csi_dev_qty = 1
csi_stby_mode = 1
csi_mname = ""
csi_twi_id = 1
csi_twi_addr = 0xba
csi_if = 0
csi_vflip = 0
csi_hflip = 0
csi_iovdd = ""
csi_avdd = ""
csi_dvdd = ""
csi_flash_pol = 1
csi_mname_b = ""
csi_twi_id_b = 1
csi_twi_addr_b = 0x78
csi_if_b = 0
csi_vflip_b = 1
csi_hflip_b = 0
csi_iovdd_b = ""
csi_avdd_b = ""
csi_dvdd_b = ""
csi_flash_pol_b = 1
csi_reset =
csi_power_en =
csi_stby =
csi_flash =
csi_af_en =
csi_reset_b =
csi_power_en_b =
csi_stby_b =
csi_flash_b =
csi_af_en_b =

[camera_list_para]
camera_list_para_used = 1
hm2057 = 1
ov7670 = 0
gc0308 = 1
gt2005 = 1
hi704 = 0
sp0838 = 1
mt9m112 = 0
mt9m113 = 0
ov2655 = 0
hi253 = 0
gc0307 = 0
mt9d112 = 0
ov5640 = 0
gc2015 = 1
ov2643 = 0
gc0329 = 1
gc0309 = 1
tvp5150 = 0
s5k4ec = 0
ov5650_mv9335 = 0
siv121d = 0
gc2035 = 1
sp2518 = 1
gc0328 = 1

[mmc0_para]
sdc_used = 1
sdc_detmode = 1
bus_width = 4
sdc_d1 = port:PF00<2><1><2><default>
sdc_d0 = port:PF01<2><1><2><default>
sdc_clk = port:PF02<2><1><2><default>
sdc_cmd = port:PF03<2><1><2><default>
sdc_d3 = port:PF04<2><1><2><default>
sdc_d2 = port:PF05<2><1><2><default>
sdc_det = port:PG00<0><1><default><default>
sdc_use_wp = 0
sdc_wp =

[mmc1_para]
sdc_used = 0
sdc_detmode =
bus_width =
sdc_cmd =
sdc_clk =
sdc_d0 =
sdc_d1 =
sdc_d2 =
sdc_d3 =
sdc_det =
sdc_use_wp =
sdc_wp =

[mmc2_para]
sdc_used = 0
sdc_detmode = 3
bus_width = 4
sdc_cmd = port:PE08<4><1><2><default>
sdc_clk = port:PE09<4><1><2><default>
sdc_d0 = port:PE04<4><1><2><default>
sdc_d1 = port:PE05<4><1><2><default>
sdc_d2 = port:PE06<4><1><2><default>
sdc_d3 = port:PE07<4><1><2><default>
sdc_det =
sdc_use_wp = 0
sdc_wp =

[ms_para]
ms_used = 0
ms_bs =
ms_clk =
ms_d0 =
ms_d1 =
ms_d2 =
ms_d3 =
ms_det =

[keypad_para]
kp_used = 0
kp_in_size =
kp_out_size =
kp_in0 =
kp_in1 =
kp_in2 =
kp_in3 =
kp_in4 =
kp_in5 =
kp_in6 =
kp_in7 =
kp_out0 =
kp_out1 =
kp_out2 =
kp_out3 =
kp_out4 =
kp_out5 =
kp_out6 =
kp_out7 =

[usbc0]
usb_used = 1
usb_port_type = 2
usb_detect_type = 1
usb_id_gpio = port:PG02<0><1><default><default>
usb_det_vbus_gpio = port:PG01<0><0><default><default>
usb_drv_vbus_gpio = port:PG12<1><0><default><0>
usb_host_init_state = 0

[usbc1]
usb_used = 1
usb_port_type = 1
usb_detect_type = 0
usb_id_gpio =
usb_det_vbus_gpio =
usb_drv_vbus_gpio = port:PG11<1><0><default><0>
usb_host_init_state = 1

[usb_feature]
vendor_id = 6353
mass_storage_id = 1
adb_id = 2
manufacturer_name = "USB Developer"
product_name = "Android"
serial_number = "20080411"

[msc_feature]
vendor_name = "USB 2.0"
product_name = "USB Flash Driver"
release = 100
luns = 2

[gsensor_para]
gsensor_used = 1
gsensor_unuse_name =
gsensor_twi_id = 1
gsensor_twi_addr =
gsensor_int1 =
gsensor_int2 =

[gps_para]
gps_used = 0
gps_spi_id =
gps_spi_cs_num =
gps_lradc =
gps_clk =
gps_sign =
gps_mag =
gps_vcc_en =
gps_osc_en =
gps_rx_en =

[sdio_wifi_para]
sdio_wifi_used = 0
sdio_wifi_sdc_id =
sdio_wifi_mod_sel =

[usb_wifi_para]
usb_wifi_used = 1
usb_wifi_usbc_num = 1

[3g_para]
3g_used = 0
3g_name =
3g_usbc_num =
3g_on_off =
3g_reset =
3g_poweron =
3g_wakeup_out =
3g_wakeup_in =

[gy_para]
gy_used = 0
gy_twi_id = 1
gy_twi_addr = 0
gy_int1 =
gy_int2 =

[ls_para]
ls_used = 0
ls_name = "ltr501als"
ls_twi_id = 1
ls_twi_addr =
ls_int =

[compass_para]
compass_used = 0
compass_twi_id =
compass_twi_addr =
compass_int =

[bt_para]
bt_used = 0
bt_uart_id =
bt_mod_type =

[i2s_para]
i2s_used = 0
i2s_channel =
i2s_mclk =
i2s_bclk =
i2s_lrclk =
i2s_dout0 =
i2s_dout1 =
i2s_dout2 =
i2s_dout3 =
i2s_din =

[spdif_para]
spdif_used = 0
spdif_mclk =
spdif_dout =
spdif_din =

[audio_para]
audio_used = 1
capture_used = 1
audio_lr_change = 0
audio_pa_ctrl = port:PG10<1><default><default><0>

[ir_para]
ir_used = 0
ir0_rx = port:PB04<2><default><default><default>

[rtc_para]
rtc_used = 1
rtc_name = "pcf8563"
rtc_twi_id = 1
rtc_twi_addr = 81

[pmu_para]
pmu_used = 1
pmu_twi_addr = 52
pmu_twi_id = 0
pmu_irq_id = 0
pmu_battery_rdc = 100
pmu_battery_cap = 2600
pmu_init_chgcur = 600
pmu_earlysuspend_chgcur = 600
pmu_suspend_chgcur = 1000
pmu_resume_chgcur = 300
pmu_shutdown_chgcur = 1000
pmu_init_chgvol = 4200
pmu_init_chgend_rate = 15
pmu_init_chg_enabled = 1
pmu_init_adc_freq = 100
pmu_init_adc_freqc = 100
pmu_init_chg_pretime = 50
pmu_init_chg_csttime = 720
pmu_bat_para1 = 0
pmu_bat_para2 = 0
pmu_bat_para3 = 0
pmu_bat_para4 = 0
pmu_bat_para5 = 5
pmu_bat_para6 = 13
pmu_bat_para7 = 16
pmu_bat_para8 = 26
pmu_bat_para9 = 36
pmu_bat_para10 = 46
pmu_bat_para11 = 53
pmu_bat_para12 = 61
pmu_bat_para13 = 73
pmu_bat_para14 = 84
pmu_bat_para15 = 92
pmu_bat_para16 = 100
pmu_usbvol_limit = 1
pmu_usbcur_limit = 0
pmu_usbvol = 4000
pmu_usbcur = 0
pmu_usbvol_pc = 4000
pmu_usbcur_pc = 0
pmu_pwroff_vol = 3300
pmu_pwron_vol = 2900
pmu_pekoff_time = 6000
pmu_pekoff_en = 1
pmu_peklong_time = 1500
pmu_pekon_time = 1000
pmu_pwrok_time = 64
pmu_pwrnoe_time = 2000
pmu_intotp_en = 1
pmu_used2 = 0
pmu_adpdet =
pmu_init_chgcur2 = 400
pmu_earlysuspend_chgcur2 = 600
pmu_suspend_chgcur2 = 1200
pmu_resume_chgcur2 = 400
pmu_shutdown_chgcur2 = 1200
pmu_suspendpwroff_vol = 3500
pmu_batdeten = 1

[boot_extend]
vol_threshold = 3600

[recovery_key]
key_min = 4
key_max = 100

[dvfs_table]
max_freq = 1008000000
min_freq = 60000000
LV_count = 7
LV1_freq = 1104000000
LV1_volt = 1500
LV2_freq = 1008000000
LV2_volt = 1400
LV3_freq = 912000000
LV3_volt = 1350
LV4_freq = 864000000
LV4_volt = 1300
LV5_freq = 624000000
LV5_volt = 1200
LV6_freq = 576000000
LV6_volt = 1200
LV7_freq = 432000000
LV7_volt = 1200
Сдвиг "тачскрина" примерно 5см вправо по оси Х, может кто знает как вылечить?

Аватара пользователя
Grey
Начинающий
Начинающий
Сообщения: 2
Зарегистрирован: 16.09.2017 13:25

Прошивка планшетов на AllWinner A10 и A13

Непрочитанное сообщение#5137 » Grey » 19.09.2017 15:22

Удалось найти решение тут: http://linux-sunxi.org/Fex_Guide#Port_Definitions

Исправленный script.fex залил на планшет работает идеально без каких либо калибровок

Код: Выделить всё

[product]
version = "1.0"
machine = "A13-EVB-V1.0"

[target]
boot_clock = 1008
dcdc2_vol = 1400
dcdc3_vol = 1200
ldo2_vol = 3000
ldo3_vol = 3300
ldo4_vol = 3300
pll4_freq = 960
pll6_freq = 720
power_start = 0
storage_type = 0

[card_boot]
logical_start = 40960
sprite_gpio0 =

[pm_para]
standby_mode = 0

[card_boot0_para]
card_ctrl = 0
card_high_speed = 1
card_line = 4
sdc_d1 = port:PF00<2><1><default><default>
sdc_d0 = port:PF01<2><1><default><default>
sdc_clk = port:PF02<2><1><default><default>
sdc_cmd = port:PF03<2><1><default><default>
sdc_d3 = port:PF04<2><1><default><default>
sdc_d2 = port:PF05<2><1><default><default>

[twi_para]
twi_port = 0
twi_scl = port:PB00<2><1><default><default>
twi_sda = port:PB01<2><1><default><default>

[uart_para]
uart_debug_port = 1
uart_debug_tx = port:PG03<4><1><default><default>
uart_debug_rx = port:PG04<4><1><default><default>

[uart_force_debug]
uart_debug_port = 0
uart_debug_tx = port:PF02<4><default><default><default>
uart_debug_rx = port:PF04<4><default><default><default>

[jtag_para]
jtag_enable = 0
jtag_ms = port:PF00<4><1><default><default>
jtag_ck = port:PF05<4><1><default><default>
jtag_do = port:PF03<4><1><default><default>
jtag_di = port:PF01<4><1><default><default>

[dram_para]
dram_baseaddr = 0x40000000
dram_clk = 408
dram_type = 3
dram_rank_num = 1
dram_chip_density = 2048
dram_io_width = 8
dram_bus_width = 16
dram_cas = 9
dram_zq = 0x7b
dram_odt_en = 1
dram_size = 512
dram_tpr0 = 0x42d899b7
dram_tpr1 = 0xa090
dram_tpr2 = 0x22a00
dram_tpr3 = 0x0
dram_tpr4 = 0x0
dram_tpr5 = 0x0
dram_emr1 = 0x4
dram_emr2 = 0x10
dram_emr3 = 0x0

[nand_para]
nand_used = 1
nand_we = port:PC00<2><default><default><default>
nand_ale = port:PC01<2><default><default><default>
nand_cle = port:PC02<2><default><default><default>
nand_ce1 = port:PC03<2><default><default><default>
nand_ce0 = port:PC04<2><default><default><default>
nand_nre = port:PC05<2><default><default><default>
nand_rb0 = port:PC06<2><default><default><default>
nand_rb1 = port:PC07<2><default><default><default>
nand_d0 = port:PC08<2><default><default><default>
nand_d1 = port:PC09<2><default><default><default>
nand_d2 = port:PC10<2><default><default><default>
nand_d3 = port:PC11<2><default><default><default>
nand_d4 = port:PC12<2><default><default><default>
nand_d5 = port:PC13<2><default><default><default>
nand_d6 = port:PC14<2><default><default><default>
nand_d7 = port:PC15<2><default><default><default>
nand_wp =
nand_ce2 =
nand_ce3 =
nand_ce4 =
nand_ce5 =
nand_ce6 =
nand_ce7 =
nand_spi =
nand_ndqs = port:PC19<2><default><default><default>

[mali_para]
mali_used = 1
mali_clkdiv = 2

[twi0_para]
twi0_used = 1
twi0_scl = port:PB00<2><default><default><default>
twi0_sda = port:PB01<2><default><default><default>

[twi1_para]
twi1_used = 1
twi1_scl = port:PB15<2><default><default><default>
twi1_sda = port:PB16<2><default><default><default>

[twi2_para]
twi2_used = 1
twi2_scl = port:PB17<2><default><default><default>
twi2_sda = port:PB18<2><default><default><default>

[uart_para0]
uart_used = 0
uart_port = 0
uart_type = 2
uart_tx = port:PB19<2><1><default><default>
uart_rx = port:PB20<2><1><default><default>

[uart_para1]
uart_used = 1
uart_port = 1
uart_type = 2
uart_tx = port:PG03<4><1><default><default>
uart_rx = port:PG04<4><1><default><default>

[spi1_para]
spi_used = 0
spi_cs0 = port:PG09<2><default><default><default>
spi_cs1 = port:PG13<2><default><default><default>
spi_sclk = port:PG10<2><default><default><default>
spi_mosi = port:PG11<2><default><default><default>
spi_miso = port:PG12<2><default><default><default>

[spi2_para]
spi_used = 0
spi_cs0 = port:PE00<4><default><default><default>
spi_sclk = port:PE01<4><default><default><default>
spi_mosi = port:PB02<4><default><default><default>
spi_miso = port:PB03<4><default><default><default>

[rtp_para]
rtp_used = 1
rtp_screen_size = 7
rtp_regidity_level = 5
rtp_press_threshold_enable = 0
rtp_press_threshold = 0x1f40
rtp_sensitive_level = 0xf
rtp_exchange_x_y_flag = 0

[ctp_para]
ctp_used = 1
ctp_name = "ft5x_ts"
ctp_twi_id = 1
ctp_twi_addr = 0x38
ctp_screen_max_x = 800
ctp_screen_max_y = 600
ctp_revert_x_flag = 1
ctp_revert_y_flag = 0
ctp_exchange_x_y_flag = 0
ctp_int_port = port:PG11<6><default><default><default>
ctp_wakeup = port:PB03<1><default><default><1>

[tkey_para]
tkey_used = 0
tkey_name = "hv_keypad"
tkey_twi_id = 2
tkey_twi_addr = 0x62
tkey_int =

[motor_para]
motor_used = 0
motor_shake =

[disp_init]
disp_init_enable = 1
disp_mode = 0
screen0_output_type = 1
screen0_output_mode = 4
screen1_output_type = 1
screen1_output_mode = 4
fb0_framebuffer_num = 2
fb0_format = 10
fb0_pixel_sequence = 2
fb0_scaler_mode_enable = 0
fb1_framebuffer_num = 2
fb1_format = 10
fb1_pixel_sequence = 2
fb1_scaler_mode_enable = 0

[lcd0_para]
lcd_used = 1
lcd_x = 800
lcd_y = 600
lcd_dclk_freq = 40
lcd_pwm_not_used = 0
lcd_pwm_ch = 0
lcd_pwm_freq = 18000
lcd_pwm_pol = 1
lcd_if = 0
lcd_hbp = 46
lcd_ht = 1056
lcd_vbp = 23
lcd_vt = 1270
lcd_hv_if = 0
lcd_hv_smode = 0
lcd_hv_s888_if = 0
lcd_hv_syuv_if = 0
lcd_hv_vspw = 0
lcd_hv_hspw = 0
lcd_lvds_ch = 0
lcd_lvds_mode = 0
lcd_lvds_bitwidth = 0
lcd_lvds_io_cross = 0
lcd_cpu_if = 0
lcd_frm = 1
lcd_io_cfg0 = 268435456
lcd_gamma_correction_en = 0
lcd_gamma_tbl_0 = 0x0
lcd_gamma_tbl_1 = 0x10101
lcd_gamma_tbl_255 = 0xffffff
lcd_bl_en_used = 1
lcd_bl_en = port:power1<1><0><default><1>
lcd_power_used = 1
lcd_power = port:power0<1><0><default><1>
lcd_pwm_used = 1
lcd_pwm = port:PB02<2><0><default><default>
lcd_gpio_0 =
lcd_gpio_1 =
lcd_gpio_2 =
lcd_gpio_3 =
lcdd0 = port:PD00<2><0><default><default>
lcdd1 = port:PD01<2><0><default><default>
lcdd2 = port:PD02<2><0><default><default>
lcdd3 = port:PD03<2><0><default><default>
lcdd4 = port:PD04<2><0><default><default>
lcdd5 = port:PD05<2><0><default><default>
lcdd6 = port:PD06<2><0><default><default>
lcdd7 = port:PD07<2><0><default><default>
lcdd8 = port:PD08<2><0><default><default>
lcdd9 = port:PD09<2><0><default><default>
lcdd10 = port:PD10<2><0><default><default>
lcdd11 = port:PD11<2><0><default><default>
lcdd12 = port:PD12<2><0><default><default>
lcdd13 = port:PD13<2><0><default><default>
lcdd14 = port:PD14<2><0><default><default>
lcdd15 = port:PD15<2><0><default><default>
lcdd16 = port:PD16<2><0><default><default>
lcdd17 = port:PD17<2><0><default><default>
lcdd18 = port:PD18<2><0><default><default>
lcdd19 = port:PD19<2><0><default><default>
lcdd20 = port:PD20<2><0><default><default>
lcdd21 = port:PD21<2><0><default><default>
lcdd22 = port:PD22<2><0><default><default>
lcdd23 = port:PD23<2><0><default><default>
lcdclk = port:PD24<2><0><default><default>
lcdde = port:PD25<2><0><default><default>
lcdhsync = port:PD26<2><0><default><default>
lcdvsync = port:PD27<2><0><default><default>
lcdgamma4iep = 22

[tv_out_dac_para]
dac_used = 1
dac0_src = 0

[hdmi_para]
hdmi_used = 0

[csi0_para]
csi_used = 1
csi_mode = 0
csi_dev_qty = 2
csi_stby_mode = 1
csi_mname = "gc0308b"
csi_twi_id = 2
csi_twi_addr = 0x46
csi_if = 0
csi_vflip = 0
csi_hflip = 0
csi_iovdd = "axp20_pll"
csi_avdd = "axp20_pll"
csi_dvdd = ""
csi_flash_pol = 1
csi_mname_b = "gc0308"
csi_twi_id_b = 2
csi_twi_addr_b = 0x42
csi_if_b = 0
csi_vflip_b = 0
csi_hflip_b = 0
csi_iovdd_b = "axp20_pll"
csi_avdd_b = "axp20_pll"
csi_dvdd_b = ""
csi_flash_pol_b = 1
csi_pck = port:PE00<3><default><default><default>
csi_ck = port:PE01<3><default><default><default>
csi_hsync = port:PE02<3><default><default><default>
csi_vsync = port:PE03<3><default><default><default>
csi_d0 = port:PE04<3><default><default><default>
csi_d1 = port:PE05<3><default><default><default>
csi_d2 = port:PE06<3><default><default><default>
csi_d3 = port:PE07<3><default><default><default>
csi_d4 = port:PE08<3><default><default><default>
csi_d5 = port:PE09<3><default><default><default>
csi_d6 = port:PE10<3><default><default><default>
csi_d7 = port:PE11<3><default><default><default>
csi_reset = port:power3<1><default><default><0>
csi_power_en = port:power2<1><default><default><0>
csi_stby = port:PB10<1><default><default><1>
csi_reset_b = port:power3<1><default><default><0>
csi_power_en_b = port:power2<1><default><default><0>
csi_stby_b = port:PB04<1><default><default><1>
csi_flash =
csi_af_en =
csi_reset_b =
csi_power_en_b =
csi_stby_b =
csi_flash_b =
csi_af_en_b =

[csi1_para]
csi_used = 0
csi_mode = 0
csi_dev_qty = 1
csi_stby_mode = 1
csi_mname = ""
csi_twi_id = 1
csi_twi_addr = 0xba
csi_if = 0
csi_vflip = 0
csi_hflip = 0
csi_iovdd = ""
csi_avdd = ""
csi_dvdd = ""
csi_flash_pol = 1
csi_mname_b = ""
csi_twi_id_b = 1
csi_twi_addr_b = 0x78
csi_if_b = 0
csi_vflip_b = 1
csi_hflip_b = 0
csi_iovdd_b = ""
csi_avdd_b = ""
csi_dvdd_b = ""
csi_flash_pol_b = 1
csi_reset =
csi_power_en =
csi_stby =
csi_flash =
csi_af_en =
csi_reset_b =
csi_power_en_b =
csi_stby_b =
csi_flash_b =
csi_af_en_b =

[mmc0_para]
sdc_used = 1
sdc_detmode = 1
bus_width = 4
sdc_d1 = port:PF00<2><1><2><default>
sdc_d0 = port:PF01<2><1><2><default>
sdc_clk = port:PF02<2><1><2><default>
sdc_cmd = port:PF03<2><1><2><default>
sdc_d3 = port:PF04<2><1><2><default>
sdc_d2 = port:PF05<2><1><2><default>
sdc_det = port:PG00<0><1><default><default>
sdc_use_wp = 0
sdc_wp =

[mmc1_para]
sdc_used = 0
sdc_detmode =
bus_width =
sdc_cmd =
sdc_clk =
sdc_d0 =
sdc_d1 =
sdc_d2 =
sdc_d3 =
sdc_det =
sdc_use_wp =
sdc_wp =

[mmc2_para]
sdc_used = 0
sdc_detmode = 3
bus_width = 4
sdc_cmd = port:PE08<4><1><2><default>
sdc_clk = port:PE09<4><1><2><default>
sdc_d0 = port:PE04<4><1><2><default>
sdc_d1 = port:PE05<4><1><2><default>
sdc_d2 = port:PE06<4><1><2><default>
sdc_d3 = port:PE07<4><1><2><default>
sdc_det =
sdc_use_wp = 0
sdc_wp =

[ms_para]
ms_used = 0
ms_bs =
ms_clk =
ms_d0 =
ms_d1 =
ms_d2 =
ms_d3 =
ms_det =

[keypad_para]
kp_used = 0
kp_in_size =
kp_out_size =
kp_in0 =
kp_in1 =
kp_in2 =
kp_in3 =
kp_in4 =
kp_in5 =
kp_in6 =
kp_in7 =
kp_out0 =
kp_out1 =
kp_out2 =
kp_out3 =
kp_out4 =
kp_out5 =
kp_out6 =
kp_out7 =

[usbc0]
usb_used = 1
usb_port_type = 2
usb_detect_type = 1
usb_id_gpio = port:PG02<0><1><default><default>
usb_det_vbus_gpio = port:PG01<0><0><default><default>
usb_drv_vbus_gpio = port:PG12<1><0><default><0>
usb_host_init_state = 0

[usbc1]
usb_used = 1
usb_port_type = 1
usb_detect_type = 0
usb_controller_type = 0
usb_id_gpio =
usb_det_vbus_gpio =
usb_drv_vbus_gpio = port:power203<1><0><default><0>
usb_host_init_state = 1

[usb_feature]
vendor_id = 6353
mass_storage_id = 1
adb_id = 2
manufacturer_name = "USB Developer"
product_name = "Android"
serial_number = "20080411"

[msc_feature]
vendor_name = "MD803S"
product_name = "USB Flash Driver"
release = 100
luns = 2

[gsensor_para]
gsensor_used = 1
gsensor_name = "dmard06"
gsensor_twi_id = 1
gsensor_twi_addr = 0x1c
gsensor_int1 =
gsensor_int2 =

[gps_para]
gps_used = 0
gps_spi_id =
gps_spi_cs_num =
gps_lradc =
gps_clk =
gps_sign =
gps_mag =
gps_vcc_en =
gps_osc_en =
gps_rx_en =

[sdio_wifi_para]
sdio_wifi_used = 0
sdio_wifi_sdc_id =
sdio_wifi_mod_sel =

[usb_wifi_para]
usb_wifi_used = 1
usb_wifi_usbc_num = 1

[3g_para]
3g_used = 0
3g_name =
3g_usbc_num =
3g_on_off =
3g_reset =
3g_poweron =
3g_wakeup_out =
3g_wakeup_in =

[gy_para]
gy_used = 0
gy_twi_id = 1
gy_twi_addr = 0
gy_int1 =
gy_int2 =

[ls_para]
ls_used = 1
ls_name = "ltr501als"
ls_twi_id = 1
ls_twi_addr =
ls_int =

[compass_para]
compass_used = 0
compass_twi_id =
compass_twi_addr =
compass_int =

[bt_para]
bt_used = 0
bt_uart_id =
bt_mod_type =

[i2s_para]
i2s_used = 0
i2s_channel =
i2s_mclk =
i2s_bclk =
i2s_lrclk =
i2s_dout0 =
i2s_dout1 =
i2s_dout2 =
i2s_dout3 =
i2s_din =

[spdif_para]
spdif_used = 0
spdif_mclk =
spdif_dout =
spdif_din =

[audio_para]
audio_used = 1
capture_used = 1
audio_lr_change = 0
audio_pa_ctrl = port:PG10<1><default><default><0>

[ir_para]
ir_used = 0
ir0_rx = port:PB04<2><default><default><default>

[rtc_para]
rtc_used = 1
rtc_name = "pcf8563"
rtc_twi_id = 1
rtc_twi_addr = 81

[pmu_para]
pmu_used = 1
pmu_twi_addr = 52
pmu_twi_id = 0
pmu_irq_id = 0
pmu_battery_rdc = 100
pmu_battery_cap = 2600
pmu_init_chgcur = 300
pmu_earlysuspend_chgcur = 600
pmu_suspend_chgcur = 1000
pmu_resume_chgcur = 300
pmu_shutdown_chgcur = 1000
pmu_init_chgvol = 4200
pmu_init_chgend_rate = 15
pmu_init_chg_enabled = 1
pmu_init_adc_freq = 100
pmu_init_adc_freqc = 100
pmu_init_chg_pretime = 50
pmu_init_chg_csttime = 720
pmu_bat_para1 = 0
pmu_bat_para2 = 0
pmu_bat_para3 = 0
pmu_bat_para4 = 0
pmu_bat_para5 = 5
pmu_bat_para6 = 13
pmu_bat_para7 = 16
pmu_bat_para8 = 26
pmu_bat_para9 = 36
pmu_bat_para10 = 46
pmu_bat_para11 = 53
pmu_bat_para12 = 61
pmu_bat_para13 = 73
pmu_bat_para14 = 84
pmu_bat_para15 = 92
pmu_bat_para16 = 100
pmu_usbvol_limit = 1
pmu_usbcur_limit = 0
pmu_usbvol = 4000
pmu_usbcur = 0
pmu_usbvol_pc = 4000
pmu_usbcur_pc = 0
pmu_pwroff_vol = 3300
pmu_pwron_vol = 2900
pmu_pekoff_time = 6000
pmu_pekoff_en = 1
pmu_peklong_time = 1500
pmu_pekon_time = 1000
pmu_pwrok_time = 64
pmu_pwrnoe_time = 2000
pmu_intotp_en = 1
pmu_used2 = 0
pmu_adpdet =
pmu_init_chgcur2 = 400
pmu_earlysuspend_chgcur2 = 600
pmu_suspend_chgcur2 = 1200
pmu_resume_chgcur2 = 400
pmu_shutdown_chgcur2 = 1200
pmu_suspendpwroff_vol = 3500
pmu_batdeten = 1

[recovery_key]
key_min = 4
key_max = 6

[dvfs_table]
max_freq = 1008000000
min_freq = 60000000
LV_count = 7
LV1_freq = 1104000000
LV1_volt = 1500
LV2_freq = 1008000000
LV2_volt = 1400
LV3_freq = 912000000
LV3_volt = 1350
LV4_freq = 864000000
LV4_volt = 1300
LV5_freq = 624000000
LV5_volt = 1200
LV6_freq = 576000000
LV6_volt = 1100
LV7_freq = 432000000
LV7_volt = 1000

Аватара пользователя
Votnavt
Интересующийся
Интересующийся
Сообщения: 21
Зарегистрирован: 13.03.2017 22:16
Модель телефона: selecline
Прошивка: s3t7in
Контактная информация:

Прошивка планшетов на AllWinner A10 и A13

Непрочитанное сообщение#5138 » Votnavt » 23.09.2017 1:45

Наткнулся на сообщение по orion tp700,
ответа не нашел, решил спросить.
Прошивка нужна, а то гапсы не работают,
то есть не входит в маркет, рутировал и новые гапсы ставил,
без изменений и камера не рабочая.
Может можно исправить, ну или прошить ? )

Аватара пользователя
Votnavt
Интересующийся
Интересующийся
Сообщения: 21
Зарегистрирован: 13.03.2017 22:16
Модель телефона: selecline
Прошивка: s3t7in
Контактная информация:

Прошивка планшетов на AllWinner A10 и A13

Непрочитанное сообщение#5139 » Votnavt » 23.09.2017 10:11

Прошил оф с сайта, маркет есть, но камера не раб. ,
какую прошивку, сходную, ему можна подогнать, можна повысить чем то на 4.2.2 ... ? :)

pupok37
Начинающий
Начинающий
Сообщения: 4
Зарегистрирован: 31.10.2014 9:51
Откуда: Кохма

Прошивка планшетов на AllWinner A10 и A13

Непрочитанное сообщение#5140 » pupok37 » 23.09.2017 12:35

Добрый день!

Помогите найти прошивку.
Заранее спасибо.

Ответить